This post may contain affiliate links. If you use these links to make a purchase, we may earn a small commission. As an Amazon Associate, All Garage Floors earns from qualifying purchases. You can read our full disclaimer here.
Two questions that we are often asked is how to recoat or apply a new coat of epoxy to an older epoxy floor that has already cured and can you apply a clear coat to an older epoxy garage floor coating? If you’ve done a little bit of research on epoxy application, then you know how important floor preparation is. So let’s discuss how to determine if your floor qualifies for a recoat and then how to prep the floor before you do.
When can you apply epoxy over an older coating?
There are many examples of when you can apply a new coat of epoxy over an older cured coating. The most common of these are for people who had previously applied a color coat and now realize that they want the glossy looks and advantages of adding a clear coat.
Sometimes it’s as simple as someone who planned a multiple coat flooring system and waited too long between coats, allowing the epoxy to cure, before applying the next coat in order to get a chemical bond.
Another reason is to renew the clear top coat. After many years of service in a busy garage, the clear top coat of an epoxy floor can start to show its age. With the proper floor preparation, you can add another coat of clear and make the floor look brand new again.
And then finally, you may have an older existing coating that is showing wear from years of heavy traffic and getting thin. As long as the floor is not experiencing any delamination issues, many times you can recoat right over a worn epoxy floor to create a brand new looking finish.
As long as the existing garage floor coating is a 2-part resinous product such as epoxy, polyurea, polyaspartic, or polyurethane, then you should be able to apply an additional coat of a compatible product without issue. However, to be safe you should always consult with the manufacturer of the new coating first.
When not to apply epoxy over an older coat
If the existing epoxy floor coating is peeling up or showing other signs of delamination, then you do not want to epoxy over it. There are bigger issues at play here that are causing the delamination. Applying a new coat of epoxy over such a coating will only lead to more problems. A complete removal of the old coating by grinding would be required.
If the coating is fairly worn with more concrete showing through than there is epoxy, then you will want to start fresh by grinding the floor.
Do not attempt to apply epoxy over existing concrete sealers. These need to be removed first as epoxy will not adhere to them. Also, floor paint is not a good base for epoxy and needs to be removed as well.
How to prep epoxy for another coat
The key to applying a new coat is to mechanically rough up the surface of the older coat to create enough bite for the epoxy to adhere to it. There are a couple of ways to achieve this.
The first is to use 120 grit sandpaper on an orbital sander or pole sander like this one at Amazon. What you are trying to do is rough up the surface, not remove it. The surface should look deglossed after sanding.
Once done, sweep up the heavy stuff and then vacuum the entire floor with a shop vac. Next, use denatured alcohol on a small towel and wipe down the entire surface. The denatured alcohol will remove all the fine dust particles, evaporate quickly, and make sure that the surface is clean.
The other option is to use a floor maintainer (buffer) with a 100 grit sanding screen. You can usually rent these fairly inexpensively from your local home improvement center. They should have the sanding screens to purchase as well.
This method will go faster than the pole sander and cover a lot of floor quickly if you have quite a bit of square feet to prep. Just remember to occasionally check the sanding screen for wear and to make sure it hasn’t clogged up. After you are done, vacuum the floor and use denatured alcohol as described with the sanding method.
If you have an older clear coat that you want to renew, then you will want to use 80 – 100 grit sandpaper or a 60 – 80 grit sanding screen first to actually remove a small layer of the coating. This will help to eliminate any deeper scratches and/or embedded dirt that has marred the finish.
Do the same if you have a worn coating that is adhered very well but has some spots where the coating has worn through to the concrete. The more aggressive grit will insure that the bare concrete will be prepped properly as well.
Floor prep such as this goes fairly quickly. Once you wipe down the floor with the denatured alcohol, your floor is ready for a new coat of epoxy or floor coating of your choice.
Ben Brookens says
Is rock solid a 2 part expoxy like reg expoxy kits Ben
Shea says
Hi Ben. Yes, it’s very similar. We have an article here about RockSolid that is very informative.
Kevin R says
I have a previous epoxy installation which was the victim of out-gassing, MVT (Moisture Vapor transmission), or blisters. Bubbles did form during the drying process and now there seems to be a foul smelling liquid oozing through where the bubbles formed. How do I repair this? The epoxy was a 100% solids from Lowes. This is an older concrete and not a new pour. The concrete was etched and dried for 48hrs prior to epoxy application. A vapor test was done with no evidence of moisture.
Shea says
Hello Kevin. The foul smelling liquid is generally and indicator of mineral rich water coming from within the concrete. Since you mentioned that it passed a moisture test, it would then be an indication that the floor was not allowed to dry fully before the epoxy was applied. Concrete can take a while to fully dry out depending on how much water was introduced. Humidity is a factor as well. If it was more humid it will take longer for the concrete to dry fully. If no epoxy primer coat is used, it’s also best to apply 100% solids epoxy when the outside temperatures are decreasing. If it’s applied while the temps are increasing, any moisture still trapped in the concrete (including air) will rise to the surface and get trapped in the coating thus forming bubbles.
The good news is that a new coating will fix the issue providing that it was not caused from moisture issues within the slab to begin with (hence the moisture test). For bubbles, it’s best to sand the surface to smooth them out and prep the surface at the same time. A floor maintainer with a 60 grit sanding screen works best and is fastest. A pole sander with 80 grit sandpaper will do the job as well, it will just take longer.
Kevin R says
Thanks for the feedback. After sanding and cleaning the area should I use a primer over the entire surface and then re-apply the 100% solids epoxy? Since the floor was sealed with epoxy, it seems the liquid is still coming through the pinholes/craters (applied about 1 month ago) Also, this concrete is in a basement work shop. What are your thoughts?
Shea says
If liquid is still oozing through the pinholes after a month, Kevin, it looks more than likely that your problem is a true moisture issue and not an issue with not allowing the concrete to fully dry before application of the epoxy – particularly since we learned it is in a basement. This can open a whole new can of worms unfortunately. Applying a new coating may result in the same issue from the same pin holes. You could apply a special epoxy moisture vapor primer and then a coat of color epoxy over that, but the original epoxy may eventually delaminate from moisture beneath it. The only way to tackle the issue and know that it will work correctly, would be to grind the epoxy off and do a calcium chloride test. If the moisture is not too high you can apply a moisture vapor barrier epoxy primer and then a coat of color epoxy.
Kevin R says
Is there a particular primer you would recommend?
Shea says
Legacy Industrial has both the standard epoxy primer and the moisture vapor barrier primer, Kevin. We would suggest giving them a call and tell them about your issue.
Bee says
Hi. Can rocksolid be over epoxy? thanks ben
Shea says
Yes. As long as you properly prep the old coating, you can apply RockSolid over it.
Ben Brookens says
Hi can I wash down garage floor and rinse off instead of using denatural alcohol after getting it rugged up b thanks ben
Shea says
You can, Ben, but it introduces water into the picture which you do not want coming in contact with a new coating. If no bare concrete is exposed, you will be OK as long as you make sure the floor is dry. If bare concrete is exposed you will need to wait a minimum of 24 hours for the concrete to release the moisture that it absorbed. What denatured alcohol does is save time and eliminate all dust. It evaporates quickly which enables you to recoat the floor immediately after it has been wiped down.
Teri says
Just did the floor with RockSolid in grey. Looked great right after applying product, then about 30 mins later we started seeing “non shiny” patches which got larger and then there were many areas like this over the whole garage floor. I figured it was just curing and decided to wait till the next day to re-evaluate it again. Nothing changed and now it’s been 2 weeks and it really looks bad, some shiney areas, some dull area, some lighter areas and some darker areas. Yuck! I’ve done 2 other homes with the basic floor coverings and never had this problem. This is the first time using “RockSolid.” What do you suggest, can it be resealed/redone. It’s rather embarrassing to show family and friends our “new” garage floor now…
Shea says
Hi Terri. Did you follow the coverage rates or did you try and stretch it a little? The biggest issue with RockSolid is that the coverage rates stated in the instructions are optimistic at best. If you tried to cover more of your floor than stated you will run into these issues. The “non shiny” areas you refer to are a matte finish that is produced when the coating is too thin. This happens if the coverage rate is stretched and/or the concrete has absorbed more of the coating than the surrounding areas. The biggest issue people have been having with RockSolid is just as you described. RockSolid is not a thick coating to begin with and it penetrates concrete very well. If you have areas that are more porous than others this can happen.
The good news is that it can be corrected with another coat. The first coat acts as the primer coat. The second coat actually goes on thicker and will be very glossy. None of the material will be lost from being absorbed by the concrete. Since you are past the 7 day recoat window, it will require that you rough up the surface with 120 grit sandpaper first in order for the new coat to adhere properly. Also, we recommend that you contact Rust-Oleum Customer Service and tell them of your problem. If you have not stretched the coverage rates, we’ve received many reports that Rust-Oleum has done a good job with helping customers out.
Ben Brookens says
Do you use reg sand paper 150 grit after doing a foot or it seems like all the grit is all worn off
Shea says
Hi Ben. If the sandpaper is being used on the coating you should not be wearing out the sandpaper that fast. The idea is to just degloss and add some roughness to the coating. You don’t need to sand through the coating. If you have some real rough areas of coating, you may want to drop down to a rougher grit such as 80-100 grit.
Susan says
Bought 22 year old home…garage floor is blue/grey with flakes….it is very dull & worn, but no peeling. How do I know if the original coating was epoxy & what can I safely recitation it with?
Shea says
Hi Susan. Pour 1/2 oz. of acetone in an inconspicuous area and let it sit for minute. Next, wipe it up vigorously with a rag. If the coating does not soften up or bleed heavily, then you have epoxy or an equivalent. If the coating has not worn thin, you can rough it up with 80-100 grit sandpaper to remove the upper most layer of dirt and debris and then recoat with a clear. This will bring much of the color back and give the coating some gloss. You will lose some flakes in the process.
Chris says
I recently applied Rust-Oleum epoxy shield coating with flakes to my garage. It’s been 6 months and I want to add epoxyshield clear finish. Do I need to sand it? Or can I apply the clear finish?
If I don’t sand it and apply, what would would be worst case? Also, I don’t park my vehicle in the garage mainly foot traffic.
Shea says
Hi Chris. Yes, you need to rough up and degloss the finish as described in the article. If you don’t, the clear coat will begin to peel up in sheets in various areas sometime soon after application.
Dave Rossi says
I have a garage floor that had a 3 step epoxy coating applied with flakes (little stones) applied on the 3rd step. The floor is 3 years old. The floor is in good condition. Do I need to apply a clear coat over the floor now and if so, how do I do it? Thanks.
Shea says
Is there a clear coat on it now, Dave? And what do you mean by little stones? Are you referring to an anti-slip grit?
Kevin E says
I put down the water based rust-oleum epoxyshield about 16 years ago with a clear on top (and anti skid). It has held up very well with only a couple of spots worn through to bare concrete (granted it’s very dull looking now). I’m looking to repaint and apply the exact same product and clear. My question is for roughing up the surface, I started with a pole sander and 80 grit sandpaper, but how much pressure should I be applying? I know the surface should be dull after sanding but it’s already dull so it’s hard to tell if it’s doing anything (also, the anti skid makes it tough to tell as well because the surface is not smooth). One other question, where the epoxy has worn off to bare concrete I assume I’m ok just to paint over it? I did hit the whole garage floor with a pressure washer (electric) and very little extra paint chipped off (so it’s on there pretty good).
Shea says
Hello Kevin. You should use moderate pressure when roughing up the surface. As long as you are producing some epoxy dust (it doesn’t take much) while you are sanding you will be fine. We suggest using the supplied concrete etch on the bare concrete areas to ensure that the new coat bonds well. Just make sure you allow those areas to dry thoroughly before application. Though you used a pressure washer for cleaning, we would also suggest that you take a scrapper to the edges were the epoxy has worn away to make sure there is not anymore loose material. As a last tip, wipe down the surface with denatured alcohol on a lint free cloth before you start the application process. This will remove the remaining fine dust and debris on the surface that sweeping and vacuuming will not get.
Kevin E says
Would it be ok if I used the concrete etch on the epoxy area as well (in other words, will it hurt anything)?
Shea says
The etch that comes with the kits will not do anything to the epoxy, Kevin, so it’s OK if it gets on the coating. Etching solutions (even acid) will not have much of an effect on coatings other than to possibly discolor or degloss them. Etching solutions only work on bare, unsealed concrete.
Stephanie Velasquez says
My husband applied one layer of the 2 part epoxy in our garage, put the flakes down and allowed it to dry before he realized that he should have put two coats of epoxy for it to be cover better as with ine coat it scratches easier. It’s been only one month since he did this and I want to know if it is safe to add a second coat on top of the current coat?
Shea says
Hi Stephanie. You can always add more coats. It requires that the surface be deglossed and roughed up with 120 grit sandpaper first. Keep in mind that more coats will not make it more scratch resistant. The quality of the coating controls that. However, multiple coats will help the coating to last longer from wear and use. A good clear coat may be a better option for you unless there are areas where the coating is thin and the color is not good.
Patricia Arzada says
I built a concrete bar, I did the fake granite finish on the surface and applied that epoxy mix from Home Depot but I under measured and now the surface looks uneven :(. Can I apply another coat over the new epoxy??
Shea says
Hello Patricia. Yes, you can apply another coat if you like. Rust-Oleum allows up to 76 hours to recoat without any additional prep. However, we would recommend sanding it with 100 grit sandpaper first to smooth it out if it seems uneven to you.
Nat says
Do i need to put a primer on my cement gallery that already had epoxy. I pressure washed it the surface is pretty rough and has very little small bare concrete spots.
Thanks
Nat
Shea says
Hi Nat. No, a primer is not needed. However, you will need to rough up the surface with 120 grit sandpaper in order to create the proper profile for the new coating to adhere. Pressure washing will not do that.
Marco says
So I used a two part waterborne epoxy from Ben Moore called corotech on my garage floor first coat went on great since then when I apply another coat I always get these little tiny particles almost like little hairs as if it was from the roller but I know it’s not the roller cause it was same type of roller I used for first coat and have used sponge roller and I still get the same results. So to make sure it wasn’t the roller I went and used a different epoxy from Sherwin-Williams and test it and came out beautiful and clean. I’ve tried and everything you can think of and same result every time!! The only thing I can think of is that I’m dealing with a bad batch the bottom of can seems to be clumpy before mixing I mix it till it’s gone but I’m thinking that’s the problem cause when I did first coat bottom of can was clean no clumps and the epoxy I got from Sherwin-Williams was clean as well no clumps. I’m losing my mind I can just go with Sherwin-Williams but I like the Ben Moore product a lot better except obviously for what I’m dealing with
Shea says
Hi Marco. The first thing you always do before mixing part-A and part-B is to mix the individual components in the can first. Components can settle and you will end up with poor adhesion or color. It sounds like you may have crystallization of the Part-A. When it crystallizes, you will get little sand like particles in the epoxy. This is usually caused from improper storage. If you spot crystallization you can usually fix it by setting the can of part-A in a pan of hot water and gently stir until it is smooth again. Also, check the technical data sheets (TDS) for each epoxy. If you are using Sherwin Williams 1000 HS, it’s a better epoxy than the Corotech. It has a higher solids content for better wear and a thicker coating.
Christina says
can I put Epoxy Plus over a floor that has Rock Solid epoxy on it?
We tried the Rock Solid and it didn’t cover nearly as beautifully as the Epoxy Plus has for us in the past. We had a floor that needed to be done quickly and couldn’t wait for the Epoxy Plus to be delivered. Even after using more product than the instructions said to, the Rock Solid didn’t turn out well at all. Very disappointed and hoping to be able to do the Epoxy Plus right on top without having to sand the floors again.
Shea says
Yes you can Christina. If the RockSolid coating is adhered well, just prep the floor as described above in the article.
Rob says
I purchased my home 1 year ago, a 1960’s home and the previous owner had done a very poor DYI epoxy job on the floor. There are parts were it has come entirely up exposing the beat up concrete, probably original. Also there are sections where the DYI-er left lumps of epoxy creating thick and raised sections.
Given the thickness of the poor job and the rough patches of the old cement I was wondering if I have to rent a concrete sander and take it all off or could I use some sort of a concrete resurfacer first to get a smooth surface onto which I would have someone apply epoxy.
Shea says
Hello Rob. You will need to rent a good concrete grinder to remove all of the old coating. This will prep the bare concrete at the same time and expose any areas that need repair. You cannot apply a resurfacer over a surface that is peeling and suspect. It would not adhere well and it too would begin to peel up.
Louis Orduna says
Hello,
Two part question.
I recently tried to apply epoxy floor coating and came to find out, I had over mixed it ,whitch caused the product to prematurely harden, before I can squeegy the epoxy on the floor.
I was then left with a floor that was , only roughly poured and not spread.
I was told to buy another kit and pour right over. Note: there is a slight rise, from the product that dried.
I applied the product and got the mix problem corrected, but when it dried, it still left the endentions, from the first pour.
First question: can I fix this with applying another 3 gallons directly over the top or do I need to rip out everything and start over??
Second question: can I apply a touch up coat to touch up patches here and there or will that compromise the flow of the origanal??
Note: this is a 3 color pigment matelic epoxy.
Thanks!!
Shea says
Hi Louis. Ugh… this could have been rectified if the vendor or manufacturer that you purchased it from would have told you to grind down the first application to begin with. You can’t just cover up a rise from misapplied product. It will telegraph through just as it did. You can’t touch up with metallic epoxy either as it will stand out. Epoxy does not blend together like paint does on a wall. What product did you use?
The coating can still be salvaged and look great, but it will require taking a grinder to the bad area to bring it down to level with the rest of the coating and blend in the edges. After that, sand the surface of the entire coating with 120 grit sandpaper to degloss the finish and then wipe it down with denatured alcohol. You should then have an entire surface that is on level to accept a final coat.
jakjak says
Had recently applied rocksolid clear coating on to my garage, while curing my hubby accidentally stepped on it. Now, I have a footprint on my floor. What is the best way to take it out or try to diminish the look of the footprint?
Shea says
Hi Jakjak. Unfortunately, about the only thing you can do is sand out the footprint and apply more RockSolid. The problem with that though is that you would have to buy a new kit. RockSolid does not sell touch up kits.
Edison says
Hello!
I applyed 1 coat of Rost-oleum Epoxy Shield to garage floor 3 days ago and I came back to see how the floor was. and its not look the way I planned to look. It looks like there’s not enough paint. Some areas are more covered than others. What can I do to give another coat over it? I spread decorative flakes on it!
Thank you.
Shea says
Hi Edison. When the coating looks that way it’s usually an indicator of spreading the coating too thin. Coatings are not like paint and you have to stay within the stated coverage rates for a one coat floor or it will look like that. Unfortunately, you are past the 48-76 hour recoat window for Rust-Oleum. What you will need to do is rough up the surface with 120 grit sandpaper as we state in the article. You will loose some color flakes, but that is OK. You can apply the new coating right over them and then apply new flakes to the second coat.
Edison says
Thnak very much!
Chuck says
Hi I purchase Rust-Oleum 2 part epoxy for garage kit put it down it turned out great I added clear coat over the top of the paint I’ve added several clear coat over the paint through the years now I noticed the clear coat is peeling up and also my garage floor by the garage door is darker color any suggestions how to bring up where it is peeling and how to get that darker color off without damaging the paint
Shea says
Hello Chuck. The darker color of the epoxy near the door is called ambering. Epoxy is not U.V. stable and areas exposed to more direct sunlight will eventually develop a yellow tint which changes the color tone of the epoxy. The only way to fix this is to apply a new color coat. Our suggestion is to sand down the clear past where it has peeled and then apply a new color coat and then clear coat. The easiest way to do this is with a floor buffer using a 40-60 grit sanding screen. The other option is to just live with the color change and sand down the clear past where it has peeled and just apply more clear.
If you want to avoid the hassle of the color changing we would suggest taking the coating down to the color coat and then apply a U.V. stable product such as this one here that will not amber. It will also last much longer since it is much more durable.
David says
Hi
I have purchased a two part solvent based epoxy from rustoleium and painted my shop floor then after it dried i have realized that there are areas where I can see the concrete through so I did not apply enough on there. So my question is can I just apply more on those areas will I see that i apply a new layer or will it blend in? I have only applied the initial coat 36 hours ago
Shea says
Give Rust-Oleum a call, Dave. They have a recoat window of 48-72 hours on their epoxy dependent upon what you used. They will be able to tell you for sure. Once you go past that window, it requires roughing up the surface with 120 grit sandpaper first before applying a new coat.
JT says
The concrete in my garage is about 1 ½ years old and about 8 months ago I put RUST-OLEUM Epoxy Shield floor coating over the garage floors. Now there are several spots that are peeling away and exposing the concrete, mostly where the vehicle tires sit on the concrete. When brushing/cleaning this area, the top layer of the exposed concrete seems to continue to break away (dusting).
I now realize when I was prepping the floors, the dust on the floors was more than just dust, it was concrete dusting and I should have used a concrete densifier and hardener before applying the Epoxy Shield to make the concrete stronger and more durable. Would I be able to grind those areas that are peeling, clean floor, spray the concrete densifier and hardener to those areas, and then add the epoxy over those areas? I will sand over the existing coat around the affected areas (6 to 8 inches) before applying the Epoxy Shield. Do you have any suggestions without removing all of the existing floor?
Shea says
Hello JT. Your concrete surface may be soft (causing the dusting) or it may have had excess laitance from the finishing process which the mild etching solutions from the inexpensive DIY epoxy paint kits will not remove. If you have epoxy peeling due to dusting or excess laitance, then your entire floor is suspect. In order to try and rectify the problem correctly, you will need to grind the floor to remove all the epoxy. The grinding will also remove any excess laitance if that was the issue.
Once you grind, you can test the surface by trying to scratch it with the edge of a screwdriver. If the screwdriver doesn’t do much or just leaves a slight mark, then you most likely had excess laitance. You can then apply your coating of choice. If the screwdriver gouges the surface, then you have concrete with a soft top and would need to treat it with a densifier. Densifiers require 7 days to react. You can then test the surface again after that. Assuming that the surface is hard enough, you will then want to test for water absorbsion. Densifiers can act like a sealer which will effectively block coatings from penetrating the concrete surface and will lead to peeling. If the surface beads water or will not absorb it well, you will need to lightly regrind in order to remove the sealing properties at the surface before applying your coating. We would also recommend choosing something better than a low solids water-based epoxy if you want your coating to last more than a few years or so.
Mary says
We want to change the color of the epoxy on our garage floor. It is in good condition (the epoxy), but we don’t like the color. Can we re epoxy another color or will epoxy paint hold over old epoxy on garage floor?
Shea says
Hi Mary. Yes, if the current coating is in good shape, all that is required is to degloss and rough up the surface with 120 grit sandpaper as we describe in the article. Once you do that, you can apply a coating of your choice to the surface.
Helen says
HI. We are reapplying a fresh coat of epoxy over existing old epoxy. Some areas have worn, so we are sanding back to the concrete, applying an epoxy primer then the top coat after this. My question is that in areas that are very solid epoxy, and don’t need sanding off, should we still apply the primer on top of this, then the top coat, or is it sufficient to just apply top coat straight onto the old coat?
Shea says
Hi Helen. After sanding the entire surface, it’s not necessary to apply an epoxy primer to the old coating that is adhered well. Applying it only in the areas of bare concrete will help with leveling out the surface and prevent creating a different tone in the color from where it covers bare concrete vs old epoxy. What primer are you using? Many people make the mistake of using a concrete paint primer thinking that it is the same as an epoxy primer coating. It is not and is not compatible.
Helen Robson says
It’s the epoxy primer we’re using. Great advice thank you. We’ve got lots of patches, however, where the concrete is showing and some very stubborn old epoxy that won’t come up. The worry is that if we put primer down all over, will it adhere to the old Epoxy enough and not cause new epoxy to peel?
Shea says
As long as the old epoxy is sanded well with a minimum 120 grit sandpaper, Helen, then the epoxy primer will adhere well. Just make sure you apply your new coating to the epoxy primer within the recoat window in order to get a good chemical bond.
Helen Robson says
Brilliant thank you Shea