As an Amazon Associate All Garage Floors earns from qualifying purchases.
Acid etching the garage floor is sometimes the only viable alternative for many DIY home owners when prepping concrete correctly to accept a coating. It isn’t hard to do, but certain safety precautions and steps need to be taken to insure a successful and safe outcome. Potentially dangerous if not done correctly, it can not only damage your concrete, it can cause serious bodily harm as well. So please take the time to learn how to acid etch your garage floor or concrete safely before jumping into your project head first.
Muriatic acid, also known as hydrochloric acid, is the typical acid of choice when etching concrete. It is inexpensive and a dangerous chemical that can damage almost anything it comes in contact with. It will eat through clothes, metal, skin, and creates a noxious vapor that can cause surrounding metals to rust as well as burn the lining in your nose and lungs. You can purchase it from your local home improvement center for less than $10 a gallon at a strength of 31.45%.
Phosphoric acid which is a mineral acid works almost as well and isn’t as dangerous to work with, but it is harder to find and more expensive. It also works at emulsifying oils – something that muriatic acid will not do. Both will remove rust from your concrete.
If you don’t like the idea of working with acid, you can read about some safer alternatives to acid etching here.
Supplies and protective gear for acid etching
- Hose with adjustable spray nozzle
- 5 gallon plastic bucket
- Plastic 2 gallon watering can
- Baking soda
- Stir stick – wood paint stick works fine
- Push broom or long handled scrub brush
- Rubber gloves
- Rubber boots
- Splash safety eye goggles
- Approved respirator for working with acid fumes
- pH paper test strips
Acid is generally mixed at a ratio of 3 parts water to 1 part acid for sufficient strength to etch properly. Ideally you want to test the strength needed first before doing the entire floor. You can do this by first mixing a small solution in your watering can starting at a 5:1 ratio. Apply it to a small area of wet concrete. It should begin bubbling and fizzing immediately. If not then you will want to increase the strength accordingly. Sometimes a ratio stronger than 3:1 may be needed for particularly dense concrete or a smooth power troweled floor.
Caution! Always add acid to water, not water to acid. If you pour water into acid it can cause an explosive reaction that can spray you with the mixture and burn your skin!
Before acid etching, make sure the garage floor is cleaned properly of all oil, contaminants, grease, and dirt. Contrary to what many people think, acid will not clean grease and oil spots. In fact, if these areas have not been cleaned and degreased properly, the acid solution will just sit on top and not react with the concrete.
1 – Dampen the concrete:
Use your hose to lightly spray down the concrete in your garage so that the concrete is wet but not puddling water. If you have a large garage floor, you may want to acid etch in sections. Do not let the concrete dry out before or during application of the acid solution.
2 – Apply the acid solution:
Use the 2 gallon plastic watering container to sprinkle the acid solution on the concrete. This will spread the solution evenly without much splashing. Do not just pour it on the concrete. This will create an inconsistent spread of the acid solution and will not provide for a uniform result. The 2 gallon container works well because you can mix 1.5 gallons of water to .5 gallons of acid for a 3:1 ratio. You can use any size you like, however, as long as you mix the ratio of acid to water correctly. 1 gallon of a 3:1 acid solution will cover approximately 50 – 70 square feet of garage floor.
3 – Scrub the acid solution:
Once the solution is applied, lightly scrub it into the concrete with a push broom or long handled scrub brush. This helps to create a uniform etch of the concrete. Let the solution sit for 10 – 15 minutes while it continues to fizz and bubble. Do not let the floor dry out during this process. Add more solution if necessary.
4 – Neutralize:
Mix 1 cup of baking soda to 1 gallon of water in your large 5 gallon bucket and pour it into the now empty watering container. Sprinkle your neutralizing solution over the part of garage floor that was acid etched and let it sit for a minimum of 10 minutes. When time is up, rinse the neutralized solution with your hose into a drain or out the garage (if local water codes allow it). Another method is to use a wet vac and then dispose of the solution according to your local codes.
Check the surface of the concrete at this time. It should feel similar to medium grit sand paper with a uniform texture. If not, you will need to repeat the process again.
5 – Final rinse:
Once the initial neutralizing solution is cleaned up, it is important to thoroughly flush and rinse the remaining solution out of the concrete multiple times. It can leave a white powdery residue (calcium carbonate) on your garage floor once dried if you do not do this. This is a fine white dust that will not allow your coating to adhere properly. Use a high pressure nozzle while thoroughly scrubbing the concrete with your scrub brush. You can introduce a mild solution of Simple Green at this point if you like. Just make sure it is thoroughly rinsed.
Using a pressure washer for this process well also. Do not use a pressure washer to rinse off the initial neutralizing solution however. It can drive any acid solution that had not been neutralized deeper into the concrete and cause problems later.
6 – pH test your rinse water:
After your final rinse, dab a pH test strip like these at Amazon onto the still wet garage floor to check the pH. Anything between 6.0 and 9.0 will work for most coatings with 7.0 (neutral) being ideal. If it’s below 6.0 then the water is indicating that acid residue is still in the pores of the concrete. Rinse some more and repeat the test until you get the results you want.
Further Tips for Acid Etching Concrete
It’s a good idea to cover anything in your garage that you don’t want to get splashed with a plastic drop cloth. Another recommendation is to mix some neutralizing solution up ahead of time and spread it out liberally on your driveway. That way any acid solution that is hosed out will not mildly etch or discolor your driveway. Don’t acid etch the concrete if the temps are below 50 degrees as the acid will not be as effective with the cooler temperatures.
Also, make sure your garage floor has dried thoroughly before applying epoxy coatings. Fans will help. Give it at least two days with warm weather and longer if it’s humid or cooler. Though the surface may be dry, the pores of the concrete can still contain moisture and escape through outgassing when the temperatures rise during the day. This will cause your coating to form bubbles. You can always do a quick moisture test with plastic if you are not sure.
Learning how to acid etch your garage floor isn’t hard, but it’s very important to follow the proper steps. When done correctly, the chances of having your coating fail due to improper preparation of the concrete is reduced significantly.