• Home
  • Epoxy / Coatings
  • Mats
  • Paint
  • Tiles
  • Sealers
  • Cleaning
  • Repair
  • Concrete Prep
  • Reviews
  • Accessories
  • Gallery

All Garage Floors

Garage flooring options, ideas, and tips

Cleaning and Maintenance Tips for Garage Floor Coatings

Updated 27 October, 2019 By Shea 129 Comments

cleaning epoxy coated garage floor

Learning how to clean an epoxy garage floor coating isn’t hard. In fact, one of the primary reasons for having a floor coating is for the ease of maintenance. There are some basic cleaning tips for epoxy floors that you should be aware of, however, that will help insure a nice clean surface for years to come. These cleaning tips are the same for polyurea, polyurethane, and polyaspartic garage floor coatings as well.

As resilient as garage floors coatings are to dirt and stains, they do require some cleaning maintenance to keep their shine. If not, some coatings can start to loose their gloss due to the sanding effect of the loose dirt and grime that gets caught up under shoes and tires.

Another issue to be aware of is that some cleaners can leave a film on the surface while others may de-gloss the shine or cause it to fade. So let’s take a look at what cleaners to use and what not to use, as well as some recommended cleaning methods.

Epoxy floor cleaning and maintenance

The first thing we recommend is getting yourself a quality 24” to 36” dust mop. You can find these at your local home improvement centers or you can purchase them from Amazon. You will find that a dust mop will provide for 90% of your epoxy floor cleaning duties.

Since dust and dirt do not stick to the floor, just use the dust mop once a week (or sooner if needed) to keep the floor clean. It only takes a few minutes and you are done. They even work well for floors that have a polymer anti-slip additive in the surface.

If you have a floor coating with an aggressive anti-slip aggregate such as aluminum oxide or you don’t care for dust mops for a particular reason, then a soft bristle push broom like this one here make for a great choice as well.

For garage floor coatings with contraction joints or saw cuts in the floor, vacuum them out monthly or use a broom to sweep them clean of debris.

Spot cleaning for spills or fluid leaks from cars can easily be wiped up with a paper towel, soft cloth, or a clean rag. A shot of Windex works wonders if the spill has left a film.

Heavy duty cleaning

For epoxy garage floor coatings that see a lot of traffic and dirt, it’s a good idea to give your floor a good cleaning once every 3 or 4 months. The best cleaning tools for this is a good quality hard foam mop or microfiber mop. Though some people swear by them, we are not the biggest fan of string mops. They just don’t scrub very well and have a tendency to leave streaks on glossy finishes.

Mops

A mop we like that works quite well for epoxy floors is this one here by Rubbermaid. It performs great at picking up dirt and debris and leaves very little liquid on garage floor coatings.

As with most floor mopping, frequent rinsing in the cleaning solution is the key for the best results. Admittedly, the self-wringing feature of this mop is a great benefit.

Another option is a microfiber mop. A clear favorite is this one here from Amazon. It’s commercial quality and has an 18″ width which helps to cover more floor to get the job done faster.

What’s nice about this mop is that it also comes with a microfiber dust mop pad. This allows it to work double duty as your everyday dust mop and regular cleaning mop which reduces the amount of cleaning tools you need to store.

Cleaning solutions

Our favorite cleaning solution that works well for regular floor cleaning is ½ cup of ammonia to a gallon of hot water in a bucket. Apply it using the foam or microfiber mop. Be sure to rinse the mop frequently in the bucket of hot water to rid it of the debris it picks up. This even works well for floors that have salt film and residue. You really shouldn’t need anything stronger than this for most jobs.

Windex is another solution that will give you a little bit more cleaning power if it’s needed. Mix a ratio of 1 part Windex to 3 parts water. The chemicals in Windex will not leave a film on the coating and do a good job of cutting through residue.

For spot cleaning any stubborn dirt that you encounter, a soft scrub pad can be used. Just don’t scrub too hard or you may degloss the surface.

If for some reason you have some serious cleaning to do, Simple Green is a product that will work well at cleaning up grease and other grime. This really shouldn’t be needed unless you have a cleaning disaster on your hands or a worn floor of lower quality epoxy that has many scratches allowing dirt to get embedded.

Start with a solution of 1 part Simple Green to 8 parts water. A deck brush helps for scrubbing in this case. You can mix it stronger if necessary, however, keep in mind that Simple Green can leave a film on the coating. The key is to use a separate bucket of clean water and mop to rinse the floor as you go.

When using any of these methods you can just let the floor air dry. You can also wipe it down with a lint free towel if you prefer.

Marks left by tires can be the toughest to remove if not cleaned regularly. You can read more about removing tire marks in a separate article here.

For rust stains, we recommend using a 1:1 ratio of CLR and warm water. Apply it directly to the rust spot using a scrub brush or soft scrub pad and then rinse with cold clean water. Do not let it sit for more than a minute or two on the surface.

Do not use these cleaners on garage floor coatings

When cleaning your garage floor coating, do not use citrus cleaners or vinegar. These types of cleaners contain acids that can slowly degloss the finish of epoxy and other floor coatings over time.

Don’t use cleaners with soap in them as well. Soap can leave streak marks and a hazy film on the surface that impedes the shine of the finish. The soapy film can also make the floor much more slippery when it gets wet.

Cleaning an epoxy garage floor coating should be easy. Just use these cleaning tips and methods for your quick and easy floor coating maintenance. Doing so will help to maintain a cleaner looking floor that will hold its gloss and finish for a longer period of time.

Related articles others have read:

  • 10 Reasons you Should Add a Clear Top Coat to…
  • How to Clean Your Garage Floor
  • Make A Plan for Organizing and Cleaning your Garage
  • Restore your Garage Floor from Road Salt and Winter Damage
  • How to Remove Tire Marks from Epoxy Garage Floor Coatings

Cleaning and Repair Cleaning Epoxy Epoxy Coatings


129 comments

  1. Clint says

    22 July, 2018 at 6:03 PM

    What product can be used over rust oleum rock solid after sanding? Floor is less then a year old and has yellow streaks and spots throughout. These are areas that do not see sunlight. I would like to use a more industrial type coating over the top… any suggestions??

    Reply
    • Shea says

      22 July, 2018 at 7:32 PM

      Hi Clint. If the RockSolid is holding down good, we would recommend something like this single-part polyurea here. It is much more durable than RockSolid and it will not yellow (amber) from sunlight.

      Reply
  2. L.C. says

    8 November, 2018 at 12:02 AM

    We just painted our floors with epoxy coating a few weeks ago. Did the proper prep and applied 2 coats. Our cat missed the litter box and the residue is an orange colored stain on the epoxy floor that wont come off. Why is this and what do you recommend to remedy this?

    Reply
    • Shea says

      8 November, 2018 at 10:50 AM

      Hi L.C. What epoxy product did you use exactly? Was a clear top coat applied? If so, what product was it?

      Reply
  3. Dave says

    30 November, 2018 at 3:58 PM

    How do I remove oil stains from an epoxy garage floor please?

    Reply
    • Shea says

      30 November, 2018 at 5:42 PM

      Hello Dave. Generally oil should not be a problem for an epoxy coating. However, if it has sat for a while on a well worn or poor quality coating then it may be more difficult to remove. Usually the use of a degreaser and stiff nylon brush can do the trick. If that doesn’t work, Goof Off has been known to remove some tougher stains from epoxy. If neither of those work, then the oil most likely has migrated into the upper surface of the coating and cannot be removed without cosmetically damaging it.

      Reply
    • Neil says

      9 February, 2019 at 10:26 AM

      How do you remove battery acid from epoxy floor. The acid has solidified and recommended products will not loosen or dissolve.

      Reply
      • Shea says

        9 February, 2019 at 12:00 PM

        Hello Neil. The typical solution for breaking down the reside of battery acid is to mix a paste of water and baking soda. This will help to loosen the residue, but it still may require scrubbing with a stiff nylon brush. Keep in mind that once it is removed, it will have most likely permanently stained the epoxy white. High performance 100% solids epoxy is the most resistant coating to acids, but it is only tested for periods of 24-48 hours. Even these high performance epoxy coatings will permanently turn white if the acid is allowed to sit for an extended length of time.

        Reply
  4. Candace says

    17 December, 2018 at 11:49 AM

    Our snow blower leaked gasoline on our new epoxy floor leaving a yellowish stain. Any ideas on how to remove?

    Reply
    • Shea says

      17 December, 2018 at 12:28 PM

      Hello Candace. The best method is to use a concrete cleaner degreaser on the stain. Lightly scrub with a nylon bristle brush. Don’t use an aggressive scrub pad or you can degloss the finish. If that doesn’t work, then it’s most likely locked into the epoxy. Epoxy will stand up to gas for a limited amount of time, but if it’s allowed to sit for quite a while it can permanently stain the finish. This is more common for the lesser quality epoxy paint kits and not quite as common for professionally installed coatings.

      Reply
  5. Nico says

    27 December, 2018 at 12:26 PM

    If the shine is fading after cleaning what is a good product to being that shine back?

    Reply
    • Shea says

      27 December, 2018 at 6:46 PM

      Hello Nico. You may be developing a thin soapy film on the surface depending on what you have been cleaning it with. Try cleaning with a 1/2 cup of ammonia to 1 gallon of hot water to remove any possible film. If that doesn’t bring back the shine, then most likely it’s due to microscopic scratches from wear. At that point there isn’t much you can do short of recoating.

      Reply
  6. Sheila says

    24 January, 2019 at 7:23 AM

    I moved into a apartment with neglected floors…the scum on them is thick. What’s the best solution to beautify my floors without causing damage…and can they be waxed?….the kitchen is the worst!

    Reply
    • Shea says

      24 January, 2019 at 10:17 AM

      Hello Sheila. What type of floors are you referring to? This article is about garage floors.

      Reply
  7. Lynn Maxim says

    30 January, 2019 at 7:51 PM

    We just purchased a home with an epoxy garage floor. There is heavy duty adhesive tape on the floor. What is the best method to remove the tape without harming the floor?

    Reply
    • Shea says

      30 January, 2019 at 11:09 PM

      Hi Lynn. Use a blow dryer or heat gun to warm the tape, slowly pulling it up as you go. For sticky glue adhesive and tape residue, Goo Gone works well without damaging the finish. Just let it soak for a few minutes before scrubbing it away.

      Reply
      • Lynn says

        31 January, 2019 at 8:19 AM

        Thank you! We will try it today.

        Reply
  8. Rose Hullinger says

    19 April, 2019 at 5:31 AM

    I have 2 questions: we have an epoxy floor that was professionally installed. How do we remove rust? You mentioned CLR, but doesn’t that have acid in it?
    There is one very small spot that has bubbled and cracked. How can we fix that?
    Thanks

    Reply
    • Shea says

      21 April, 2019 at 10:08 PM

      Hello Rose. Yes, CLR has some mild acids in it. You need that to dissolve rust. When using it on a rust stain, you have to use it sparingly and only on the rust. Try not to wipe much of the area around it. What has bubbled and cracked? Is it the coating?

      Reply
  9. Randy says

    2 June, 2019 at 10:29 AM

    I had a can of black enamel paint leak onto my professionally installed epoxy garage floor. The spot is about 1 foot square. How can I remove the sport without damaging the epoxy?

    Reply
    • Shea says

      2 June, 2019 at 10:36 PM

      Hello Randy. We always recommend contacting the installer first to inquire since we don’t know exactly what was used as a top coat. If you can’t get the info from the installer, we recommend dabbing the paint with mineral spirits or MEK. Try to use as little as possible since solvents can degloss some coatings.

      Reply
  10. Bryan says

    3 September, 2019 at 7:32 PM

    Hi I recently put and epoxy flake floor with a polyaspartic topcoat. The topcoat was General polymers 4850. It turn out nice but I miss a tiny spot and after I try mixing a tiny bit of the A and B components to to cover the missed spot. Well the polyaspartic sets in about 15 mins and it has been 2 days and this tiny amount has not set and and I dont think ever will. Now I need to remove it and am not sure as to what chemicals i can safely use to remove it. The data sheet says to clean tools with mek after use…. can i safely use this on my floor to remove the remaining unsolifidified polyaspartic mixture or will I damage the cured product trying to do this? Any info would be greatly appreciated. Thanks

    Reply
    • Shea says

      4 September, 2019 at 10:40 AM

      Hello Bryan. MEK can be used (not mineral spirits) as it tends not to leave a residue. However, it can also quickly degloss a coating so you want to use it judiciously. Clean as much of the uncured coating off first so that you don’t have to use much MEK.

      Reply
  11. Marcie Patten says

    10 September, 2019 at 4:30 PM

    I was trying to remove heavy-duty double sided carpet tape from my concrete floor. I used Goo Gone which removed the majority of the adhesive but resorted to acetone to get the harder to remove areas up. Well………….. you guessed it! I removed adhesive, and the sealer and have exposed concrete in small areas in front of shop entrance. I do not know what product/type of sealant was used on the floor- this was done 10 years ago and before I bought the business. What do you recommend I do to re-seal the areas affected?

    Reply
    • Shea says

      10 September, 2019 at 10:35 PM

      Hello Marcie. We’re sorry to hear what happened. Unfortunately, we can’t provide a good solution without knowing exactly what was used. Your best bet is to prep the surface with 40 grit sandpaper and recoat the area with a similar color and product. It won’t look perfect, but it will protect the concrete.

      Reply
  12. Ken Ivey says

    22 November, 2019 at 7:16 PM

    I had a bleach bottle leak on my garage floor. It is epoxyed in dark grey. I have a white spot where it leaked, any way to clean it? Thank you in advance!

    Reply
    • Shea says

      23 November, 2019 at 1:50 PM

      Hi Ken. Unfortunately, straight bleach that is allowed to sit for a period of time can do that. It reacts with the epoxy over time and causes a permanent white spot.

      Reply
« Older Comments

Leave a Reply to L.C. Cancel reply

Your email address will not be published. Required fields are marked *
Questions and comments are moderated before they are published.

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Latest Featured

Rubber gym flooring in a garage

Discover these Top Gym Flooring Options for the Garage

posted on 24 November, 2019

all-weather-floors-polyurea-review

Why AWF Polyurea has Earned the Status as a Top DIY Garage Coating

posted on 25 October, 2019

bridjit-rolled-curb-ramp-driveway

Our Review of the Best Curb Ramps for Driveways and Raised Garage Floors

posted on 25 September, 2019

diy-acid-stained-garage-floor

This Dazzling 6 Color DIY Acid Stained Garage Floor Pops with SPGX Clear

posted on 31 August, 2019

Our Sponsors

  • Concrete Sealers USA
  • Click Here For More Information.
  • polyurea garage floor coating
  • Premium Garage Epoxy Flooring
  • Compare Best Epoxy Flooring-Garage Floor Tiles & Rubber Roll Out Mats
  • Armorpoxy High Performance Epoxy Coatings
  • epoxy-coat
  • Rust Bullet DuraGrade Concrete Coating
  • Concrete Sealers and Coatings

Most Popular

best-floor-jacks-garage

Our Review of the Top 5 Floor Jacks for Your Garage

grinding garage floor with diamabrush rental

How to Grind Your Garage Floor With This Easy Method

garage snow

Choosing the Best Garage Floor Mats for Snow and Winter

repairing-pitted-garage-floor

How to Easily Repair Your Pitted and Spalled Concrete

pet-urine-odor-concrete

How to Eliminate Pet Urine Odors from Concrete and Basements

best-garage-floor-coating-kit

Why the Best DIY Floor Coating Kits are Single-Part Polyurea

how to apply garage floor epoxy

How to Apply an Epoxy Garage Floor Coating – A DIY Guide

  • Home
  • About Us
  • Site Map
  • Reader’s Projects
  • Options and Ideas
  • Advertise

What we do

All Garage Floors is the most comprehensive resource on garage flooring that you can find today. We are here to help you with the latest information about garage floor coatings, garage tiles, floor paint, garage floor mats, concrete sealers, and more.

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.

Enjoy!

Follow Us

Get the latest updates on flooring ideas, tips, storage, and all those cool garage accessories.

Contact Us

Have a question or submission? Just let us know here! Proud of your own project? Just send us your project info for consideration to be displayed on our Reader’s Projects page.

Contact Us

Copyright © 2019 All Garage Floors · All rights reserved | Privacy Policy | Terms of Use

Return to top of page

This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish.Accept Reject Read More
Privacy & Cookies Policy

Necessary Always Enabled