There is an abundance of confusion today among homeowners looking to apply paint or a coating to their garage floor. Should it be epoxy paint or an epoxy coating? Is there a difference? If so, which is best? It’s not always easy to tell since many of the DIY garage floor kits available today use these terms interchangeably.
As a result, it is very important to learn the distinction between paint, epoxy paint, and epoxy coatings. Doing so will eliminate confusion and enable you to make an informed decision. This is vital if you want to obtain the expected looks and performance for your garage floor.
We are the first to acknowledge that the marketing for DIY paint and epoxy can be misleading. If you don’t know EXACTLY what type of product you are purchasing, then you may end up being one of the unhappy consumers with ruined expectations for epoxy flooring.
What is Epoxy Paint?
The term “epoxy paint” came about years ago when paint and coating manufacturers took notice of the terminology that the DIY public was using when searching for epoxy garage floor coatings. They were intermixing “paint” with “coating” without knowing the difference.
As a result, marketing decisions were made and many well-known DIY epoxy floor coating companies decided to brand their products as “epoxy paint” since that is what consumers seemed to be calling it.
Unfortunately, it has only made things more confusing for the consumer. Chances are that when you see something advertised as epoxy paint for your garage, it could be 1-part epoxy paint or it could be an epoxy coating.
This has led to many people buying paint for their garage floor when what they thought they were purchasing was an epoxy coating. This is why it’s so important to learn what epoxy paint and epoxy coatings are.
Commercial quality DIY epoxy kits available from concrete coating vendors online are called coatings. As a result, there is no confusion.
Epoxy Coatings are not Paint
The first misnomer that we want to address is that an epoxy coating is not paint. The two are not chemically compatible and should not be used together whenever possible.
Paint consists of 4 basic ingredients. The first three are pigments, binders, and additives. The fourth is a carrier agent that these ingredients are suspended in. This will be primarily water or solvents.
Once applied, the pigments, binders, and some additives are deposited onto the concrete as the carrier agent evaporates out during the drying process.
The binders are what provide performance, support, and adhesion for the pigments. They bind or hold them together in a thin film on the concrete surface. Most garage floor paints are water-based and use latex acrylic polymers to bind the pigments together.
Typical additives include thickening agents and surfactants. They provide for easier application and prevent pigments from separating.
The amount of pigment, binders, and additives that are left on the surface after drying is referred to as the solids content. It is measured by weight and volume.
Volume is what determines how thick the paint will be and how much material is left on the concrete after evaporation when applied at the recommended coverage rate. Most concrete paint has a solids content of 29-33%. The rest is water and some solvents.
This means that once applied, the wet film thickness (WFT) of the paint shrinks approximately 67-71% as the water evaporates out. What you are left with is a very thin dry film thickness (DFT) of approximately 1.0 mils. A sheet of paper is roughly 3 mils thick for reference.
Garage floor paint is the least expensive option and the poorest performing. Most standard concrete paints for porches, patios, and garages use a latex acrylic binder. Though latex may work well for walls, it’s not a good match for garage traffic.
Paint does not seal the concrete. It will peel up from hot car tires. Solvents, brake fluid, gas, and other harsh chemicals will discolor and many times soften the paint. This can cause it to smear or delaminate when cleaning up.
In addition, it is only available in a satin finish and is not intended for clear coats. We get many questions about clear coats for paint which we discuss here.
The primary benefits of concrete paint are that it’s cheap and fairly easy to touch up. In essence, paint is a short-lived and budget-minded option.
What is 1-Part Epoxy Paint?
1-Part epoxy garage floor paint uses modified latex acrylic binders as well. However, it also includes a small amount of epoxy ester resin as an additive. The epoxy resin helps the acrylic binders to create a more durable paint film with better adhesion properties. However, it is not an epoxy coating.
The amount of epoxy resin is not included in the technical data sheets. This is because listing the exact additives is not required. However, it is not much since the average solids content is only 1-4% greater than standard concrete paint. As a result, the DFT is only slightly thicker at 1 – 1.5 mils.
Like standard latex acrylic garage floor paint, 1-Part epoxy paint is not a sealer, it is only available in a satin finish, and is not intended to be clear coated. Some may be marketed as paint and primer in one.
And no matter how big or bold the print on the can states that it is “hot tire resistant”, it WILL peel up from hot tires at some point. Just not as fast as standard concrete paint.
It will resist some automotive chemicals, salt, and grease better than standard concrete paint, but the increase in resistance is not substantial.
It does wear a little longer, particularly under foot traffic. If vehicle traffic will not be introduced, then 1-Part epoxy paint can be a good budget option for a garage or workshop that won’t see heavy use or exposure to strong chemicals.
See our Recommended Picks for 1-Part Epoxy Paint
If paint is the only option in the budget, then spending a few dollars more per gallon for 1-Part epoxy paint over standard concrete paint is worth the investment.
What Makes an Epoxy Coating Different than 1-Part Epoxy Paint?
An epoxy coating is a two-component thermosetting polymer. It consists of one part epoxy resin and one part polyamine hardener. The hardener acts as a catalyst. When the two parts are mixed before application, a chemical reaction is started that results in an exothermic or heat-generating process.
Once the two parts are mixed, you are limited by time and temperature as to how long you have to apply it. This is referred to as the pot life.
The resin component is tinted to give the epoxy color. The hardener component is always clear. If the resin component is not tinted, then it is considered a clear epoxy.
Unlike paint that binds into a thin film while it dries, epoxy chemically cures. The chemical reaction creates a tight cross-linking of the two components. This forms an extremely hard and durable coated surface that seals the concrete and can be highly stain and chemical resistant.
In addition, it achieves a much stronger bond than paint when applied to a properly prepared concrete surface. Epoxy requires etching the concrete at the minimum (as do most coatings) before application.
Furthermore, subsequent coats that are applied during the recoat window will achieve an extremely strong chemical bond with each other. Paint cannot do this.
How thick and how well an epoxy coating performs is determined by the quality of the epoxy resin, formula, and most importantly, the solids content. Generally, the higher the solids content, the better performing epoxy will be.
Epoxy coatings for concrete and garage floors can have a solids content that ranges from 42% – 100%. The solids content will also determine the length of the pot life and ease of application.
Low solids epoxy can have a pot life of up to two hours. It is usually applied with a roller out of a paint tray. Rust-Oleum EpoxyShield is an example.
High solids epoxy can have a pot life as short as 30 minutes and needs to be poured out onto the concrete in ribbons immediately after mixing. It is then spread around by a squeegee or roller and then back rolled to finish. If left in the bucket, it will get hot and be unusable within minutes.
The less expensive DIY epoxy paint kits that you can buy at your local home improvement center or hardware store are water-based and have a semi-gloss finish. Colors are typically limited to Tan/Beige and Gray. They have an average solids content by volume of 42-53%.
When applied at the recommended coverage rate, they will achieve a dry film thickness of 2.5 – 3.5 mils. This type of epoxy is easier to apply as well as cheaper to buy. It goes on the floor almost as easily as paint does.
Easy application is one of the primary marketing points that makes these kits so popular to purchase. They can be applied to your garage floor more easily compared to premium high solids epoxy.
Read: Learn What to Expect with Inexpensive DIY Epoxy Kits
Commercial quality epoxy kits can have a solids content ranging from 80-100% and typically have a very glossy finish. In addition, they are available in a large range of colors other than tan and gray.
The dry film thickness for commercial quality, high solids epoxy can range from 8 – 12 mils when applied with a roller. 100% solids epoxy can be applied even thicker in one application.
High solids epoxy is more durable, it hides imperfections in the concrete better, it does not experience hot tire pickup, and lasts years longer. In addition, it is more stain and chemical resistant than lower solids epoxy.
Read: Learn the Basics of How to Compare Epoxy Coatings
The pot life for high solids epoxy can range from 30 – 50 minutes depending on the temperature and solids content. It can be a little more difficult to work with during application because of the thicker viscosity and limited time to apply it.
Though the pot life is limited, it can still be easily applied in the required amount of time as long as you plan your application steps out ahead of time. Our article on garage floor coating application explains this in detail.
Final Thoughts
Whenever in doubt about what you are purchasing, always review the technical data sheets. These will detail exactly what type of product you are purchasing. In addition, they provide very important information regarding application and durability.
So don’t fall for the epoxy marketing name game when deciding on what you want to apply to your garage floor. As you can see, epoxy paint and epoxy coating may or may not mean the same thing. Do your research first, as this will help you to understand the type of epoxy you are purchasing and what kind of results to expect.
susan says
I am getting ready to re-do a sunroom(south facing) to make it functional as a living space. It was renovated years ago, but has been used as an aviary for many years. The floor is concrete that had been painted, but the paint is in poor shape now. This room will be used lightly (mostly as a reading and relaxing in room) and I am needing advice on what kind of finish should be put down this time. Epoxy seems to be overkill, but plain paint doesn’t seem adequate. Suggestions?
Shea says
Hello Susan. Since the room is just seeing foot traffic, a 1-part epoxy paint would be a good choice. They are easy to apply and can be ordered in a variety of nice colors. This is an example here from Seal-Krete. Due to the U.V. exposure from being a sun room, a true 2-part epoxy will amber (yellow tint). Be sure to scrape up all the loose paint you can before you apply it.
VP says
Can you explain what is 2 part epoxy?
Shea says
Hello VP. 2-part epoxy is explained in detail in the article. If you look back over the article you will find a full explanation.
John potter says
I have a flat roof over my garage. I installed salittio tile on the roof.. Will the 100 percent coat seal the tile so there is no leaking down below..??
Shea says
No, it won’t John. It’s the wrong product for the job. Epoxy is an indoor concrete floor coating and does not do well exposed to the sun.
M Swartz says
A small section of my garage…about 4′ x 8 feet was enclosed and a floor covering was installed. The linoleum is deteoriatinf, hard to get clean. I would like to pull up the floor covering and replace with garage floor paint.
What do I need to know about this application?
Shea says
The most important thing you must do is remove all the old glue from the concrete before painting. Once you pull the floor up it will most likely require grinding to remove the glue residue from the surface and the pores of the concrete. You can try a chemical stripper instead of grinding, but it may or may not remove the glue from the pores. It will require that you do a water drop test after the concrete has dried. If the concrete readily absorbs the water then it will be ready for paint. If the water beads at the surface without being absorbed, then that means the glue is blocking the pores and will require that you grind. The paint needs to penetrate the surface of the concrete in order to bond correctly.
Dennis says
Hi,
I do not understand what is the mixture of latex acrylic and epoxy coating.
Shea says
Hello Dennis. I’m not sure what you are asking really. We explain the differences in the article. Latex acrylic paint is basically the same water based product that you apply to the walls on the inside of your house. Epoxy is a 2-part thermosetting polymer that reacts when mixed together. If cures (does not dry like paint) to a very hard coating.
William says
I would like to paint the basement floor. It will be used for storage only. With the ceiling height only 5ft, so I have several pallets with casters mounted on it to make moving things around easier. It will not be a lot of traffic. 1 part epoxy paint will do the job? Or I better use 2-part epoxy paint?
Shea says
Hi William. If you are rolling around pallets on casters then a 2-part epoxy will be better suited for that. Just make sure you don’t have any issues with moisture in the slab or either type of product will delaminate.
Mark says
Have aa basement with a concrete floor that is not in good shape. If I use levelor to fill in and level the floor can I then put a 1-part epoxy on the floor?
Shea says
Yes you can, Mark. Make sure it’s an actual polymer-modified concrete repair material and not a self-leveling underlayment like you can buy at your local home improvement centers. Underlayments are not made for fixing such issues and they are not paintable. They are also not a wear surface. Their purpose is to lay wood flooring, tile, linoleum, or carpet on top.
Stacy Johnson says
I have asbestos tikes in my basement, and I’m looking to see if a 2 part epoxy would work to cover over these and level out my basement floor. Do you see this causing any issues? This would be our rec room. No water issues in the basement.
Shea says
Hi Stacy. You have to be very careful with asbestos tiles. Epoxy can be used to coat over them, but it has to be a commercial product. Also, the surface needs to be roughed up with sandpaper before application of epoxy in order to achieve a mechanical bond. This creates asbestos dust which is dangerous. Additionally, epoxy should not be used to level floors. You would need an epoxy slurry for that and it can get very expensive.
Ken says
I’m about to build a commercial kitchen. Should I be looking for an epoxy coating or a high quality 2-part epoxy paint? Also, do you have any leads on how to achieve a cove around the perimeter of the room?
Shea says
Hello Ken. There is 2-part epoxy or latex acrylic paint. There is no such thing as a combination of the two. 2-part epoxy paint is still epoxy. It’s just a confusing way of marketing it to make people think it’s like paint, but it isn’t. You need a commercial quality 2-part epoxy or similar product for a commercial kitchen. Most of the vendors that sell commercial coating products also sell the thick formulations that are used to form a cove base as well. It generally requires a special trowel to help form it. We suggest contacting someone like ArmorPoxy to discuss your options. You will not find what you need from a home improvement center.
mike m says
Hello question,
I have a small townhouse with a small 20×10 patio in the backyard that gets 50% of the sun (In Arizona). Previously there was an old grey paint that I had to remove via a concrete grinder and acid wash. I wanted to rejuvenate this area and was thinking about putting an epoxy down from Sherwin Williams but then read your comment about Epoxy not being UV-Proof.
What recommendation do you have for me? Thanks. I would like to paint/epoxy the area to make it look nicer again.
Shea says
Hello Mike. Yes, epoxy is not a good medium for outdoor use. Unlike paint, floor coatings that are used outdoors can be very slippery when wet as well. An anti-slip additive is important to use. Though more expensive, a proper coating can last years and years outdoors where as paint will most likely last a couple years or so before it needs to be touched up or redone. Polyurea, polyaspartic, and polyurethane coatings are the ones that are typically used outdoors. They are generally a slightly different formula than those used on garage floors and they have anti-slip options as well. We recommend contacting either Legacy Industrial or ArmorPoxy and ask them about their outdoor coatings for your project. If you decide on paint instead, a 1-part epoxy would be the best bet. Since they are mainly latex paint, they are U.V. resistant as well. Seal-Krete offers the best color palette by far.
rich bohane says
We have latex paint over our concrete garage floor. We would like to put rustoleum epoxy coating over it. Can we do this, if so what prep do you recommend.
thanks
Shea says
Technically you can, Rich, as long as you are using the standard water based epoxy and not their Professional series which is solvent based. It requires that you rough up the surface of the paint with 120 grit sandpaper in order for the epoxy to achieve a mechanical bond to the paint. However, we don’t recommend it. The reason is that the bond of your overall coating is only as good as what is adhered to the concrete. In other words, the superior bonding characteristics of epoxy to concrete will be lost since it will be bonding to the latex paint instead. Latex paint tends to peel from concrete, so the entire coating will peel if the latex paint does. In order to ensure the best performance, we recommend grinding the concrete to remove the paint first. This will also prep the concrete for a coating at the same time.
Shannon says
I have put a two part epoxy on my basement floor and loved the results it gave me in helping fill and level (small) divot in my floor. We decided to paint the walls with an epoxy paint. To make it a little less expensive I purchased a one part epoxy paint (before doing my research; dumb idea) I painted one wall and it is not filling in the pores of the concrete like my floor. My question is do you think it will fill with a second coat or should I go spend the money on the two part epoxy coating?
Shea says
Hi Shannon. Epoxy floor coatings are not designed for wall paint. They will begin to slump and run if you try to apply them very thickly since gravity is working in the wrong direction, unlike a floor. Our suggestion is to use filler on your walls first and then paint them just as you would normally do.
peter says
hi, i am peter from ghana africa, we have a very big car park lot. we want to do marking on the pavement floor,as in parking lots can we use epoxy coating or what is your advice. thank you
Shea says
Hello Peter. No, epoxy will not work because it is not U.V. resistant. It will turn a chalky white color and deteriorate in the sun. Also, most coating will not adhere properly to asphalt since it is oil based.
Dan B says
Great Info here.
Dan from Canada.
I have an older car I want to keep going for another year. Works great, but the Oil Pan is getting badly worn.
I hope to wash it well and remove all oil with solvents, then 100% epoxy paint it. This would give it wear protection for a year, I hope.
I understand cured epoxy is resistant to gas and oils. Also there should not be any UV. Some hot (not extreme) temperatures and snow / sand / water / etc abrasion.
A 200$ oil pan would not be a good investment here, and I like puttering in my retirement.
Ready, aim, shoot me down!
Shea says
Hello Dan. If you are talking about an oil pan for a car, then no, it’s not going to work. Epoxy starts to soften between 150-160 degrees. Oil can get well over 200 degrees.
Dan says
Thanks
Much effort saved
Dan
Tyler Demas says
Hi! Thanks for all of the great articles! Before reading all of your wonderful articles I purchased Seal-Krete brand Epoxy-Seal concrete and garage floor paint and began to paint and spread color flakes. I finished half of my two car garage before I realized it wasn’t providing the shine or overall smoothness I remember seeing in my mother’s garage (she claims to have used this same product). It also wouldn’t fill in the tiny cracks in the concrete as I expected it would. My question is what can I use to put a glossy finish in the garage floor paint with color flakes in it? Also, what can I use to fill in those tiny cracks without breaking the bank or ruining the work I’ve already done? I’m on a relatively tight budget. And I typically do all of my own vehicle repairs/maintenance, and do the same on friends’ vehicles, so I tend to get the occasional oil drips, or brake fluid drops, or etc etc. Thank you so much for reading, and thank you even more if you respond with some advice.
Shea says
Hi Tyler. Unfortunately the problem is with the product you are using. You will not get the shine, durability, or thickness from paint like a high solids epoxy or similar coating will provide. Paint shrinks quite a bit when it dries and is why it will not cover small spider surface cracks. You can’t really put shine into it as well. Clear coats help, but paint is not designed for clear coats. You can use Rust-Oleum concrete crack repair on the cracks. It is not very expensive providing that you don’t have too many cracks. Also, keep in mind that brake fluid will soften the paint fairly quickly if it’s not wiped up. Even then it may stain.
Our suggestion is to continue painting the rest of the floor without spending any more money. Save up and then when the budget allows for it, grind the paint off and apply a proper epoxy coating system for the type of work you like to do in your garage.
Liz says
I would like to use an epoxy paint to refurbish my concrete / marble sheen pool. What do you recommend? Pool size is approx 90sq metres.
Shea says
Hi Liz. Epoxy garage floor coatings are not made for such use. They are an indoor coating only. Also, U.V. rays from the sun will cause the epoxy to oxidize over the years. You would need a special polyurea spray on coating for pools if you want to use a similar technology. They are usually applied by professionals.
Anita says
I have removed old vinyl tiles from basement floor. There now are some holes, cracks visible as well as old adhesive. How can I prepare this floor to finish with epoxy.
Shea says
Hi Anita. All the old adhesive needs to be removed and the holes and cracks repaired. Grinding the concrete is the quickest and easiest way to remove the old glue. It will also prep the surface for epoxy at the same time. If you elect not to grind, then you will need to remove the glue via chemical means. There are ECO friendly products available that work well, they just take longer to work and it gets messy. After the glue is removed via chemical means you can then etch the concrete to prep it for epoxy.
Tynmoon says
Hi,
Can I apply epoxy coating to tiled toilet floor which is heavily used daily say in the public toilet.
Shea says
No, you can’t apply epoxy to a tiled floor Thynmoon. The surface is too smooth and the coating will peel right up.
Michelle says
Thank you for all of the effort you put into your articles and answering questions. Very professional.
Shea says
Thank you, Michelle.
dana says
I am specifying a 2-part epoxy coating for a dental office. The rooms are on the window side of the building. The client wants it to look like an airplane hanger, in gloss and in white. My understanding 2 part epoxy system will yellow with UV rays. What is your recomendation
Shea says
Hello Dana. White coatings take a little more work, but they can look nice if done correctly. It generally requires a base build coat of white epoxy followed by one or two coats of white polyurethane. The white base epoxy is needed since any other color underneath would affect the look of the white polyurethane. The polyurethane is U.V. resistant and will not amber. We suggest contacting an experienced vendor for such a project.
harry says
“This has lead to many people buying”
The word is led, not lead.
Shea says
That is correct! Thanks for pointing that out, Harry.
Anne says
I have a finished basement and I want to paint the concrete floor. What kind of paint should I use?
Shea says
Hello Anne. If you want to paint the basement floor and not apply a coating, we would recommend a good 1-part epoxy paint. We have an article about them here.
Gene Gawryleski says
I am considering covering my garage floor which is 12 years of age with a covering. Do you think that the 1 part epoxy will do the trick. I am 69 years old just keep that in mind. my basic question with proper prep work will the 1 part coating last say 10 to 20 years with car usage and one pickup truck ?
Shea says
Hello Gene. No, 1-part epoxy paint will only last a few years. It is essentially a fortified paint and is not a high performance coating. A common complaint is hot tire pickup within the first few months of applying it – sometimes sooner. It generally needs to be reapplied after a few years or so in order for it keep looking nice. You cannot apply a clear coat to 1-part epoxy paint either. If you want something that will last 10+ years and is fairly easy to apply, we highly recommend one of the newer single-part polyurea coatings.
Danye'll says
Thank you for your wonderful article. I have concrete floors inside of my house. I want to use the marbalized method with the epoxy. When they say metallic epoxy floors are they referring to the metallic pigment ? Can I use this on my floor?.
Shea says
Yes you can, Danye’ll. RockSolid has a DIY version which we discuss in this article here. You can also apply a tougher and more exotic type of metallic coating with the type of kits we discuss here.
Jan says
We are considering buying an older home that appears to have an “epoxy treated/painted” floor in the garage. It is an estate sale so no one appears to know what the prior treatment was. Also, the present color of the floor is a maroon! Since so little is known regarding this issue, would we need to do a complete grind to remove the prior coating/painted floor of the garage or what would you recommend? Thanks in advance for your advice!
Shea says
Hello Jan. Yes, maroon is not common and an indicator that it may be paint and not a true coating. If it’s paint, it is highly recommend to remove it via grinding if you want to apply a true coating. If it is epoxy (or something similar) and it is adhered well, then you can get by with just roughing up the surface with 120 grit sandpaper first. You can generally test for a coating by applying a liberal amount of acetone on on the floor and then rubbing it hard with a rag. If the colored surface gets soft or bleeds out onto the rag, then you have paint. If it just loses gloss and stays hard, then it’s a true coating.