There is an abundance of confusion today among homeowners looking to apply paint or a coating to their garage floor. Should it be epoxy paint or an epoxy coating? Is there a difference? If so, which is best? It’s not always easy to tell since many of the DIY garage floor kits available today use these terms interchangeably.
As a result, it is very important to learn the distinction between paint, epoxy paint, and epoxy coatings. Doing so will eliminate confusion and enable you to make an informed decision. This is vital if you want to obtain the expected looks and performance for your garage floor.
We are the first to acknowledge that the marketing for DIY paint and epoxy can be misleading. If you don’t know EXACTLY what type of product you are purchasing, then you may end up being one of the unhappy consumers with ruined expectations for epoxy flooring.
What is Epoxy Paint?
The term “epoxy paint” came about years ago when paint and coating manufacturers took notice of the terminology that the DIY public was using when searching for epoxy garage floor coatings. They were intermixing “paint” with “coating” without knowing the difference.
As a result, marketing decisions were made and many well-known DIY epoxy floor coating companies decided to brand their products as “epoxy paint” since that is what consumers seemed to be calling it.
Unfortunately, it has only made things more confusing for the consumer. Chances are that when you see something advertised as epoxy paint for your garage, it could be 1-part epoxy paint or it could be an epoxy coating.
This has led to many people buying paint for their garage floor when what they thought they were purchasing was an epoxy coating. This is why it’s so important to learn what epoxy paint and epoxy coatings are.
Commercial quality DIY epoxy kits available from concrete coating vendors online are called coatings. As a result, there is no confusion.
Epoxy Coatings are not Paint
The first misnomer that we want to address is that an epoxy coating is not paint. The two are not chemically compatible and should not be used together whenever possible.
Paint consists of 4 basic ingredients. The first three are pigments, binders, and additives. The fourth is a carrier agent that these ingredients are suspended in. This will be primarily water or solvents.
Once applied, the pigments, binders, and some additives are deposited onto the concrete as the carrier agent evaporates out during the drying process.
The binders are what provide performance, support, and adhesion for the pigments. They bind or hold them together in a thin film on the concrete surface. Most garage floor paints are water-based and use latex acrylic polymers to bind the pigments together.
Typical additives include thickening agents and surfactants. They provide for easier application and prevent pigments from separating.
The amount of pigment, binders, and additives that are left on the surface after drying is referred to as the solids content. It is measured by weight and volume.
Volume is what determines how thick the paint will be and how much material is left on the concrete after evaporation when applied at the recommended coverage rate. Most concrete paint has a solids content of 29-33%. The rest is water and some solvents.
This means that once applied, the wet film thickness (WFT) of the paint shrinks approximately 67-71% as the water evaporates out. What you are left with is a very thin dry film thickness (DFT) of approximately 1.0 mils. A sheet of paper is roughly 3 mils thick for reference.
Garage floor paint is the least expensive option and the poorest performing. Most standard concrete paints for porches, patios, and garages use a latex acrylic binder. Though latex may work well for walls, it’s not a good match for garage traffic.
Paint does not seal the concrete. It will peel up from hot car tires. Solvents, brake fluid, gas, and other harsh chemicals will discolor and many times soften the paint. This can cause it to smear or delaminate when cleaning up.
In addition, it is only available in a satin finish and is not intended for clear coats. We get many questions about clear coats for paint which we discuss here.
The primary benefits of concrete paint are that it’s cheap and fairly easy to touch up. In essence, paint is a short-lived and budget-minded option.
What is 1-Part Epoxy Paint?
1-Part epoxy garage floor paint uses modified latex acrylic binders as well. However, it also includes a small amount of epoxy ester resin as an additive. The epoxy resin helps the acrylic binders to create a more durable paint film with better adhesion properties. However, it is not an epoxy coating.
The amount of epoxy resin is not included in the technical data sheets. This is because listing the exact additives is not required. However, it is not much since the average solids content is only 1-4% greater than standard concrete paint. As a result, the DFT is only slightly thicker at 1 – 1.5 mils.
Like standard latex acrylic garage floor paint, 1-Part epoxy paint is not a sealer, it is only available in a satin finish, and is not intended to be clear coated. Some may be marketed as paint and primer in one.
And no matter how big or bold the print on the can states that it is “hot tire resistant”, it WILL peel up from hot tires at some point. Just not as fast as standard concrete paint.
It will resist some automotive chemicals, salt, and grease better than standard concrete paint, but the increase in resistance is not substantial.
It does wear a little longer, particularly under foot traffic. If vehicle traffic will not be introduced, then 1-Part epoxy paint can be a good budget option for a garage or workshop that won’t see heavy use or exposure to strong chemicals.
See our Recommended Picks for 1-Part Epoxy Paint
If paint is the only option in the budget, then spending a few dollars more per gallon for 1-Part epoxy paint over standard concrete paint is worth the investment.
What Makes an Epoxy Coating Different than 1-Part Epoxy Paint?
An epoxy coating is a two-component thermosetting polymer. It consists of one part epoxy resin and one part polyamine hardener. The hardener acts as a catalyst. When the two parts are mixed before application, a chemical reaction is started that results in an exothermic or heat-generating process.
Once the two parts are mixed, you are limited by time and temperature as to how long you have to apply it. This is referred to as the pot life.
The resin component is tinted to give the epoxy color. The hardener component is always clear. If the resin component is not tinted, then it is considered a clear epoxy.
Unlike paint that binds into a thin film while it dries, epoxy chemically cures. The chemical reaction creates a tight cross-linking of the two components. This forms an extremely hard and durable coated surface that seals the concrete and can be highly stain and chemical resistant.
In addition, it achieves a much stronger bond than paint when applied to a properly prepared concrete surface. Epoxy requires etching the concrete at the minimum (as do most coatings) before application.
Furthermore, subsequent coats that are applied during the recoat window will achieve an extremely strong chemical bond with each other. Paint cannot do this.
How thick and how well an epoxy coating performs is determined by the quality of the epoxy resin, formula, and most importantly, the solids content. Generally, the higher the solids content, the better performing epoxy will be.
Epoxy coatings for concrete and garage floors can have a solids content that ranges from 42% – 100%. The solids content will also determine the length of the pot life and ease of application.
Low solids epoxy can have a pot life of up to two hours. It is usually applied with a roller out of a paint tray. Rust-Oleum EpoxyShield is an example.
High solids epoxy can have a pot life as short as 30 minutes and needs to be poured out onto the concrete in ribbons immediately after mixing. It is then spread around by a squeegee or roller and then back rolled to finish. If left in the bucket, it will get hot and be unusable within minutes.
The less expensive DIY epoxy paint kits that you can buy at your local home improvement center or hardware store are water-based and have a semi-gloss finish. Colors are typically limited to Tan/Beige and Gray. They have an average solids content by volume of 42-53%.
When applied at the recommended coverage rate, they will achieve a dry film thickness of 2.5 – 3.5 mils. This type of epoxy is easier to apply as well as cheaper to buy. It goes on the floor almost as easily as paint does.
Easy application is one of the primary marketing points that makes these kits so popular to purchase. They can be applied to your garage floor more easily compared to premium high solids epoxy.
Read: Learn What to Expect with Inexpensive DIY Epoxy Kits
Commercial quality epoxy kits can have a solids content ranging from 80-100% and typically have a very glossy finish. In addition, they are available in a large range of colors other than tan and gray.
The dry film thickness for commercial quality, high solids epoxy can range from 8 – 12 mils when applied with a roller. 100% solids epoxy can be applied even thicker in one application.
High solids epoxy is more durable, it hides imperfections in the concrete better, it does not experience hot tire pickup, and lasts years longer. In addition, it is more stain and chemical resistant than lower solids epoxy.
Read: Learn the Basics of How to Compare Epoxy Coatings
The pot life for high solids epoxy can range from 30 – 50 minutes depending on the temperature and solids content. It can be a little more difficult to work with during application because of the thicker viscosity and limited time to apply it.
Though the pot life is limited, it can still be easily applied in the required amount of time as long as you plan your application steps out ahead of time. Our article on garage floor coating application explains this in detail.
Final Thoughts
Whenever in doubt about what you are purchasing, always review the technical data sheets. These will detail exactly what type of product you are purchasing. In addition, they provide very important information regarding application and durability.
So don’t fall for the epoxy marketing name game when deciding on what you want to apply to your garage floor. As you can see, epoxy paint and epoxy coating may or may not mean the same thing. Do your research first, as this will help you to understand the type of epoxy you are purchasing and what kind of results to expect.
H j says
Nice article
Floor epoxy and wood epoxy ,are they the same or they are different?
Shea says
Hello HJ. Wood epoxy is formulated different than epoxy used for concrete floor coatings. Some concrete coatings can be used on wood, but epoxy for wood should not be used as a floor coating. It would be much more expensive to apply and the abrasion characteristics are different for starters.
Dharmendra says
Is epoxy fire proof paint??
Shea says
Hello Dharmendra. Epoxy is not paint. This article explains the difference between epoxy and paint. Epoxy formulations can be obtained that are fire resistant, but not fire proof.
Joshua says
Hello, about 20 years or more ago I made a water fountain and coated it with an epoxy paint purchased at Wellborn paint. It was 1 quart alone; not 2-part, and it has lasted all this time greatly. It started to fade and deteriorate a couple of years ago so I bought the 1-part epoxy Behr concrete and garage floor paint because the paint I used originally wasn’t available where I first bought it. I coated the fountain with the Behr paint (satin) and I don’t have too much confidence in it. I was going to give it a second coat today but it doesn’t seem as thick or as glossy or the color that I preferred; I’ve taken the gallon can back twice to adjust the color and the technician said that putting too much color pigment in it will make it less strong. I’d like to get some epoxy paint like I originally used. I was wondering if you had any advice. Thanks, Joshua
Shea says
Hello Joshua. The Behr 1-part epoxy paint is just latex paint. It has a little bit of epoxy added to aid in adhesion and wear, but that’s it. I’m not sure what you applied before, but it could not have been epoxy. Epoxy requires that you mix the resin (part-A) with a catalyst (part-B) in order for it to react and cure. Also, if exposed outdoors it will amber (turn yellow) and even begin to chalk. You may want to check with one of the vendors that offer a single-part polyurea. We have an article here with links to them. Single-part polyurea can take U.V. light and outdoor exposure. You may be limited by color selection though.
PJC says
I’m restoring some antique encaustic (concrete/clay-based) tiles. I need to fill in some larger chips/flakes around the edges created while they were salvaged. Having used epoxy fillers for other projects, I believe that will work to fill in divots, but I’d like to find small quanities of epoxy paints in primary colors plus white, black, & brown. Do you know of any brand or source? The tiles are floor tiles.
Shea says
Hello PJC. We are not aware of anyone who sells such a product in colors like that. Epoxy requires the mixing of a part-A resin and part-B catalyst (hardener) in order to activate. What you may be able to do is purchase small sizes such as these from Hobby Lobby or equivalent hobby shop. You can choose the 5 minute fast cure or longer 30 minute cure. You can then tint the part-A resin with something like this. Keep in mind that clear epoxy is not water clear. It actually has a yellow tint to it. So you need to keep that in mind when tinting for color.
JD says
Hello, are all epoxy coatings inherently glossy? Or are there any available with matte/flat finishes? Thanks!
Shea says
Hello JD. Most epoxy floor coatings are gloss to semi gloss. However, there are some polyurethane clear coatings that you can apply to epoxy that are matte in finish. This would tone down the gloss. We suggest you contact ArmorPoxy and tell them you are looking for a matte finish floor coating and see what they can do for you. They supply many large commercial flooring contractors across the U.S. and may have what you need.
JD says
Great, thanks!!
Shelli Latta says
Hello and I have a Question. I live in our old 60 year old home. We were in a Hurricane that caused flooding to 3 feet inside our home. We were about to pull up the entire kitchen floor and replace it with thick plywood. Come to find out after pulling the main floor off, we had the most beautiful Oak Planks. So we decided to keep those and we did sand them, put polyurethane over them. But, there are pieces that are sticking up and they can be bad on the feet. Also, there are some wide spaces where the planks don’t meet. I was wondering if I could put the epoxy over the floor to cover up the nails that stick up, but mainly the splintering wood?
Shea says
Hello Shelli. Epoxy should not be used for repairing real wood floors. It will not fill gaps in the wood either. If the floor was sanded properly you should not have edges of boards sticking up. Splinters that stick up just above the surface should be repaired by inserting carpenters glue under the splinter and then press it back in place. Hold it down for 12-24 hours with strong tape or a heavy object with a flat bottom. Any nails that are sticking up should gently be pounded into the wood just below the surface using a punch. Any remaining cavities in the wood (including where nails are) should be filled with wood putty. Once the glue and putty has dried sufficiently, sand and then apply the polyurethane.
Bren says
Hi! We are building a steel home on a concrete slab foundation. The home is quite large for a single level @ 4,320 sq ft. We are a multigenerational family, with 11 residents in the home…we live in the country, have a small farm, and two of our kiddos have special needs…our floors are going to take a beating! However, we do not have the $12k-$15k we are being quoted for an epoxy finish. Do you think it would be possible for us, as a family, to do a project this big? Room by room, of course. The most challenging room would be the kitchen/dining/ great room combo…27’x36’. Any recommendations?
Shea says
Hello Bren. It can be done, but you will have to take in some considerations before you do. Proper concrete prep is important for floor coatings. It requires profiling the surface, which in your case would require grinding in most circumstances. You can’t acid etch inside the home. Also, some products will produce VOC’s when first applied, but they will rapidly dissipate within 24 hours. This isn’t really an issue if no one is residing within the building yet, but it can be if there is.
We suggest contacting ArmorPoxy and speak with them about your desired project. They are a very large floor coating supplier and contractor with an extensive line of product. They are very helpful and can make some recommendations based on your requirements. Depending on product, you should easily be able to complete your floors for 1/3 of what you are being quoted.
Tarek says
Can I use epoxy flooring on the walls (plaster finished), and what is the steps to do it on the walls? it needs a potty or primer enough?
Shea says
Hello Tarek. No, epoxy is not designed as a wall coating and will not adhere well to plaster. Also, due to the slow cure times and thickness of the coating, it can begin to run when applied to such a smooth surface.
Tarek says
Thank you dear for your clarification, and is there a special kind for using on the plaster?
Shea says
No there is not, Tarek. Epoxy coatings are not designed for plaster walls and you will not find anyone who sells epoxy for such.
ajit thakur says
Can 2-part epoxy be applied on an already existing epoxy coating on concrete floor?
Shea says
Yes it can, Ajit. This article explains how.
Mike says
Hi Shea
I recently used Behr Granite Grip on my garage floor. I prepped the floor correctly removing any oil/grease stains. I then used an acid wash to etch the surface. After the floor dried i tested a few spots to verify that water was absorbed into the cement and not beading. I also let the product sit for a week after applying it before driving on it.
This past winter with the ice and snow melt on to the garage floor i noticed bubbles. The bubbles seemed to be filled with water. Once the water penetrated under the paint it just spread until a small bubble grew much larger……
My question is …can i apply epoxy 2 part system over the top of this paint to prevent water from penetrating the painted surface.
Thanks in advance
Shea says
Hello Mike. Did you do a moisture test before you applied the paint? Water bubbles under paint or a coating is a big sign of moisture that has migrated up through the slab to the underside of a coating. If you don’t have a moisture issue you can apply an actual epoxy coating. However, paint and epoxy are not very compatible. You will want to remove the paint first since paint does not adhere well to concrete and makes for a poor base.
grace says
Hi, I’ve seen rubber-like applications in children’s playparks in the UK. Wondered if this is also epoxy..?!
Shea says
Hi Grace. No, it’s not epoxy. Epoxy cures to a very hard coating that is not flexible at all.
Kathy Nelson says
We have an older home built in the 1930s and would like to update our basement floors with epoxy. The original concrete was not poured as smooth and flat as new homes so has some “rolling” areas. There are also some patched areas where a new furnace was installed, new drain pipes replaced, etc. We’ve gotten a few quotes from companies to come do the work. One company advised against epoxy suggesting that the concrete was probably ready to be replaced – suggested polishing instead. This made me wonder if applying epoxy on older concrete would compromise it in some way. Another company would clean up/prep our basement concrete and apply a “breathable” epoxy since there is no vapor barrier under the concrete like in newer houses. We have no water coming into the basement and have no structural cracks in the floor. Do you have any thoughts about applying breathable epoxy to concrete that 90 years old.
Shea says
Hi Kathy. I would stay away from the company that recommends polishing. If they stated that the concrete was ready to be replaced, then no amount of polishing is going to fix that. Regardless, polished concrete is not a good option for a basement. There is something funny going on there.
The company that recommends a special breathable epoxy is right on the money and would be a more trusted source. Ask if they do a moisture test before performing any work. Although your basement may not be wet, moisture vapor can still be coming up from beneath the slab. As long as it’s not too much vapor the breathable epoxy will allow it to pass and not hinder the coating. Ask about the concrete prep they do as well. Grinding is the preferred method and helps to smooth out and hide all the transitions where the concrete has been repaired or replaced in the past. Make sure that all work, including prep and materials, is put down in writing.
Devi says
Hi I purchased the performance epoxy-coat from Lowes and was wondering if I can mix that set with a n epoxy-seal concrete and garage floor paint to do the interior of my home
Shea says
Hello Devi. Epoxy-Coat is a highly durable 2-part resinous coating while the Epoxy-Seal is a latex paint. They are not compatible, they cannot be mixed together, nor can one be applied on top of the other. This article here explains the difference.
Deedee says
Hi 🙂 Can you epoxy over the Behr Garage and Floor Paint in a small space (say a bathroom) to seal it and prevent excessive wear/flaking where furniture rests/rubs on the painted surface?
Shea says
Hello Deedee. Paint is not designed to be clear coated and is not compatible with most actual coatings. The solvents in these coatings will soften the paint and bleed through during application. The only actual coating you can apply is a water based epoxy coating. Valspar clear epoxy is one of the few lesser expensive examples. The water-based coating will not soften the paint. It will require that you rough up the surface of the paint with 120 grit sandpaper first in order to provide the mechanical grip necessary for the epoxy.
An easier solution would be a clear acrylic sealer. These do OK and will not require that you sand the paint first. They will provide a clear glossy look and lock in the paint chips. These type of clears are designed for certain paints and masonry, but they are not a tough coating like epoxy. They work best for foot traffic only. This is an example from Behr.
Kevin says
Hi, thanks. Great info. I’m (re)doing my basement slab floor. I had it ground down, I thoroughly cleaned it, filled all cracks and then did a layer of “drylok clear” on the basement floor to reduce moisture intrusion. Now I want to do an epoxy coat. What do you recommend? It’s about 350 sq ft. I want to more than just a low solids epoxy paint such as drylok E1. Any advice hugely appreciated.
Shea says
Hello Kevin. There are a few issues with applying an epoxy coating to your basement floor. The first is that you applied the Drylok Clear. Epoxy should be applied to properly prepared bare concrete. Drylok Clear is essentially a water based acrylic coating. It’s a breathable clear coating that seals the top surface from moisture (spills and such) and still allows for moisture vapor from below the slab to escape through the coating to the surface. This is what helps to prevent the coating from delaminating and is the reason it does well in basements. Epoxy on the other hand is not breathable and seals out both moisture and vapor on both sides. If you have any moisture in your basement floor, it will eventually cause the epoxy to peel. Also, the only type of epoxy you can apply to an acrylic coating is water-based epoxy. Other epoxy (except 100% solids) and similar coatings have solvents which will soften the acrylic clear coating. It will require that you degloss and roughen the finish with 120 grit sandpaper before installation. Also, water-based epoxy has a semi-gloss finish and is not as glossy as other coatings (if that is a concern for you). Additionally, the epoxy can peel up easier if your basement has moisture. This is due to the fact that the epoxy is actually adhered to the acrylic coating and not the concrete. If your basement has never had any issues with moisture or dampness, then you can install a higher quality coating. However, it will require that you remove the acrylic coating first.
Kevin says
Thank you Shea for this clarity. I will go with a water based epoxy coat so and see how that goes. I’ll stay within the Drylok family for simplicity and use their E1.
Shea says
Just to make sure you are clear on things, Kevin, Drylok is not epoxy nor is it a true coating. It’s an acrylic latex paint that is fortified with a little bit of epoxy resin mixed into the paint. That is why it’s called a 1-part epoxy paint.
Kevin says
ahh, OK thanks again Shea. Is there a product you could please recommend instead? Meaning a water based (non solvent) epoxy (I don’t want to have to degloss and roughen the floor again) that I can apply on top. Sincere thanks.
Shea says
Hi Kevin. You can use any brand of water-based epoxy. EpoxyShield by Rust-Oleum is an example. However, there isn’t any epoxy that you can apply on top without deglossing and sanding it first. It needs the mechanical bite to adhere or it will peel. Just keep in mind that it will not adhere as well as epoxy does to bare concrete. The clear Drylok is what is keeping everything bonded to the floor.
Mike says
I have too much stuff in my garage!
That being said I’d like to do a two part approach to the floor. What product would be best for that? Basically so I can clear one side, apply the paint or epoxy coating, then move the stuff back and do the other side. Thx.
Shea says
Hello Mike. Do you have contraction joints in the garage floor? If so, you can use those as a natural border and then use any product that you want. If you don’t have those joints, then you are limited to garage floor paint or a 1-part epoxy paint. The reason is that regular paint blends well when one coating overlaps another – similar to paint on a wall. Epoxy and other coatings do not blend in that manner. It’s very obvious where one coat overlaps and rolls over another. The problem with concrete paint and 1-part epoxy paint, however, is that it does not hold up very well in a garage unless it’s mostly foot traffic.
Mike says
Thanks it is mostly foot traffic. I’m also concerned with moisture issues so was leaning towards paint or one part epoxy. Just curious, I suspect the bonding is better in higher temperatures? Was planning to do it in higher temps or have a couple of portable heaters running.
Shea says
Paint and 1-part epoxy paint is breathable and will do better will moisture vapor. The bonding will not be any better or worse as long as it is applied within the temperatures specified in the data sheets for the product you choose.
Mike says
Thanks for all the help Shea. I really learned a lot from this site!
I’m leaning towards a UGL 1 Part Epoxy Platinum Color. I was curious… If I do two coats what is the best strategy for adding flakes? Is it better to add them with the first or second coat?
Also… I did see a sample of the Epoxyshield Metallic at my local retailer. Very impressive looking! I really liked the red color options. My question… I get heavy sunlight certain times of the year. I saw on the Mother Daughter video they had some issues with UV and had to apply a different type of coat at the front of the garage. Is the UV thing still an issue with the Polycuramine?
Thanks again!
Shea says
Hi Mike. You always add color flakes to the last color coat. Just keep in mind that you cannot apply a clear coat over the color flakes of 1-part epoxy paint if that was your plan. Yes, the polycuramine by Rust-Oleum and RockSolid (same product different label) are not U.V. stable and will amber from direct sunlight.
Mike says
Right, I wasn’t thinking clearly when I asked about the flakes. Logically on the second coat since you are covering the first coat (in my case with a 1 part epoxy not a clear coat).
I’ve started my prep work and I’m really floored no pun intended by the extent of my moisture problem. I may need to grind rather than etch. You had mentioned paint or 1 part epoxy for my sectional approach, any thoughts on the moisture issue as far as paint vs epoxy? Really concerned about what the moisture will do to the epoxy over a multi year period and was starting to think a paint and periodic repaint might even be better. Thanks..
Shea says
Grinding vs etching has no bearing on a moisture issue, Mike. If you feel that it’s worse than you thought, then you may need to take a step back and re-evaluate things and consider other options. Remember, 1-part epoxy paint and concrete paint are essentially the same. They are both a latex acrylic paint that is breathable. However, both will still peel right up if you are getting visible moisture at the surface. They do OK with moisture vapor, but not visible moisture. An epoxy coating is a definite no go when moisture is present. One option would be to treat the concrete with a densifier to help slow down moisture intrusion and then consider something like interlocking tiles.
Mike says
Shea- reading through some of the comments. If you’ve applied a 1 part epoxy and want a glossier look… the option is to cover with an acrylic sealer?
The 1 part epoxy really does seem to be more like a paint. It definitely shows imperfections and I’ll be surprised if I can get flakes to adhere on the 2nd coat. No regrets though, it’s an improvement over standard concrete. And kind of a fun learning project.
Shea says
You are correct on both counts, Mike. 1-part epoxy is acrylic latex paint with a small amount of epoxy resin added. It does not have the same properties of a true 2-part epoxy coating. A water-based acrylic clear coat is about all you can feasibly apply. We’re glad you are having fun with it.
Mike says
Yeah too bad. The flakes really look great but the underlying coat of 1 part paint/epoxy is just so thin.
So no chance I could roll on a thicker top coat of epoxy, polyurethane or polyurea?
Shea says
Polyurea is a no go, Mike, due to the solvents in it. A water-based polyurethane or epoxy can be applied, but unfortunately you will lose many color flakes during the prep as mentioned. The only clear that can be applied without the prep is a water-based acrylic. The problem with that is it does not stand up well in a garage environment. Any solvents or gas that are spilled on it will cause it to soften and make a mess. Plus, hot tires can be a potential problem as well.
Mike says
Interesting. I wonder if the polyurethane option could be done via a sprayer? I’ve seen that for wood projects. That would allow for easier application. I don’t mind losing flakes either way. Any recommendations on brands? Most of what I’ve seen in the store is minwax wood type polyurethane. I’ve got a clear coat epoxy picked out if I go that route.
Shea says
No, polyurethane cannot be sprayed on for a floor coating. As I stated earlier, home improvement centers do not carry polyurethane for concrete floors either. I left a link for an example of where you can purchase water-based polyurethane for concrete coatings. You can find it here if you missed the previous link.
Mike says
Sucker for trial and error! I testing a small patch of epoxy vs. PolyUrethane (both cheap sub quality ). Think I like the PolyU better. I like the self leveling aspect of epoxy but it seems challenging to work with and we get sunlight. I worked with Epoxy for surfboards and always was frustrated with the short pot life.
For the PolyU… Is there a comparison between the Legacy and SUPERCOAT brands? The tech sheets are not apples to apples in format but both appear to be 52% solids by volume.
As always- your help is MUCH appreciated!
Shea says
Keep in mind that epoxy for surfboards is not the same formula and pot life as epoxy for floors. In terms of the two different polyurethanes you are looking at, The SuperCoat product has ratings that are more vague. However, one particular number you need to review is the Taber abrasion ratings. Abrasion ratings are exponential. A coating with a 4mg loss on a Taber Abrasion wheel vs a coating with an 8mg loss would last 3 times longer in terms of wear and not twice as long as one would assume. The SuperCoat water-based polyurethane has a rating of 33mg loss, while the Legacy Industrial product has a 10mg loss. Though the Legacy product is twice as much in cost when you break it down, it will wear at least 6 times longer. You will always get what you pay for with coatings.
Mike says
Hello Shea, H
How would the Legacy Polyurethane compare to a clear coat epoxy (such as EpxoxyShield or Valspar)?
Ideally I’d like to use both – epoxy then top it off with a coat of Legacy. Or would that be redundant?
Shea says
We have an article here that explains how polyurethane and epoxy compare, Mike. To be honest, it’s quite a gamble and investment to put two different clear coats over a 1-part epoxy paint. You still run the same risk of the paint peeling despite what you put on top of it. I would recommend doing either one or the other, but not both. The polyurethane is going to wear better, give you better chemical resistance, and will be U.V. stable, but you need to weigh the risk of the extra expense of it over the clear epoxy if the paint does not hold.
Rockin says
We purchased a 45 year old home in FL on a concrete slab with no moisture barrier. I’ve ripped up all the old tile and carpet. I’m desperately researching to find a product that is preferably low VOC and still will seal and stick to a damp concrete floor. The goal is to waterproof in a way that will not bubble or chip and provide a permanent barrier under new flooring (not carpet…maybe a solid core luxury vinyl plank or wood laminate). Are either epoxy or a 1 part epoxy paint an option or will both lift with the water vapor pressure in the damp slab? A product called Radonseal failed to improve the moisture issue at all (the reason I chose it was bc they company said it would work beautifully in my situation and that you can put anything over the top…even paint). I know if epoxy fails, I will have a huge mess on my hands, so I’m scared and frustrated by the previous failure and wasted money. Any suggestions or advice would be appreciated. help, help, help…
Shea says
Hello Rockin. Products like RadonSeal are basically a densifier. They help to fill open capillaries in the concrete to slow water intrusion, but they are not a sealer. The first thing you need to do before applying anything is to find out exactly how much moisture your floor expels. I suggest you read this article and purchase a few of the calcium chloride kits. You will be able to calculate how many moisture pounds of flow that your concrete expels. It it’s under 20lbs, there are special moisture vapor blocking epoxy primers that can be applied. They are made specifically for issues such as yours. Regular epoxy will not work and will peel. It will require that you give the concrete an aggressive grind before application as well. Etching is not good enough. These special epoxies need a rough and porous surface to adhere to. This product here by Legacy Industrial is an example. It’s 100% solids so it will be low in VOC’s as well. They are located in Florida and deal with these issues daily. I suggest you give them a call once you figure out how much moisture you have.
Joshua says
Hello, I’m a professional house painter, but I’ve never worked with epoxy. I’m looking too do a motorcycle frame and was going to go with powder coating, but a local auto painter said he would do a epoxy / urethane bc out was more durable to chipping and degreasers. And me being a painter I’m looking to do three project myself. I was gonna buy appliance epoxy, but couldn’t find a clear coat or primer for that paint. What would you recommend, i would prefer a rattle can, but i can also mix and use a spray gun. Is the urethane he spoke about. The actual clear coat? Thanks in advance
Shea says
Hello Joshua. Epoxy coatings for floors are much different than those used for painting metal. Marine epoxy enamel comes to mind. Sorry, but we can’t help you with a recommendation there. Yes, the urethane can be both a clear coat or color coat. Polyurethane is the actual material, but somewhere along the line painters adopted urethane for short.
Ellen Bell says
Hello! I am painting an outdoor brand new concrete basketball court, i want to paint it a solid color with a logo on it. Was wanting to know if the Behr garage concrete paint will hold up on it?
Shea says
Hello Ellen. It will hold up for a while, but it should not be used for a sports surface as paint can be slippery. I would recommend going with a special outdoor acrylic product designed for basketball and tennis courts. Here is an example from ArmorPoxy. This type of surface is much safer and will last longer.
Jeff Murphy says
Hello! I recently applied a two part rustoleum Epoxy system to a garage floor. I clear coated it with Rock Solid two part clear coat. After a week, I washed my car and parked it inside. The dripping water left white cloudy stains that won’t come off. What would cause this and how can I fix it? Thanks, Jeff
Shea says
Hi Jeff. RockSolid has a 7 day recoat window. This is do to the slow curing process it goes through. As a result, water should not be introduced to the floor until sometime after that. The white cloudy stains are a result of the polycuramine reacting to the water and may be moisture that is trapped in the surface. One trick that sometimes works with water spots on a coating that has not fully cured is to apply some heat to the spots with a heat gun. Be careful not to get the surface too hot. Sometimes a blow dryer will work. If that doesn’t do it, then the only way to fix the problem is to sand out those spots and apply more clear.
Jeff Murphy says
I should have been more clear in my last reply. I am not interested in using Rock Solid again as the water is still staining it after a month since application. I want a simple fix in a one part component. I’m fearful the eater based acrylic may stain the floor as well! But something too “hot” May have a bad reaction with the rock solid. I heard some good things regarding H and C. Acrylics have come a long way from what I understand. I would love your thoughts on this.
Thanks Shea,
Jeff Murphy
Shea says
I would not recommend the H&C clear glaze coat, Jeff. An acrylic coating is an inferior clear coat to what you have now. It is not going to be nearly as durable, scratch resistant, or chemical resistant as RockSolid polycuramine, epoxy, polyurethane and etc. If you don’t feel comfortable working with a 2-part product, then we suggest using a single-part polyurea clear coat. You can read about them here. We also include sources for purchase.
Jeff murphy says
Ok, thanks Shea. I figured you were going to advise against the acrylic. I am considering the NOHR-s single part polycurea. I will sand over the rock solid and perhaps wipe it with a quick shot of acetone. After a month, Water is still staining the floor which leads me to believe that the Rock solid did not cure properly. So I’m goin to sand it out , clean it and apply the polycurea. And other suggestions before I start would be greatly appreciated. I appreciate the hard work and valuable insight you have helped me and many other with.
Jeff Murphy
Shea says
That would be an excellent choice, Jeff. When you sand it down, don’t worry if you reach the color coat. It will look all scratched up and dull, but once you apply the clear it will bring the gloss right back. Just be sure to wipe the floor down with denatured alcohol on a microfiber pad for the final cleaning. Don’t use acetone as some products can leave a residue that will interfere with the coating.
Elaine says
I just finished the garage floor prep then applied the primer and one coat of 1part epoxy paint. Now I read all these comments that it won’t hold up to a winter with salt. What should I do now. Should I apply the second coat and maybe a topcoat? Or put on a 2 part epoxy? Can it go on top of 1 part paint?
Shea says
Hi Elaine. Unfortunately, a coating is only as good as what it is attached to. If you apply a 2-part epoxy over the top it will still be susceptible to hot tire pickup and all the other potential issues that a 1-part epoxy paint is known for since the epoxy is not attached to the actual concrete. Our suggestion is to either grind it off and apply a quality coating or just live with it through the winter and remove it afterwards.