One primary objective for many homeowners is to seal the concrete of their garage floor in order to protect it from water intrusion, dusting, road salts, pitting, and most importantly, to help resist stains. If you are looking for the best value and without concern about having the latest decorative finish or coating for your garage floor, then a siliconate penetrating concrete sealer may be all that you need.
Why? Although decorative garage floor coatings such as epoxy look great and do a good job of sealing the concrete, there are people who have simple “working” garages. They are not as concerned about how nice a concrete sealer looks, but rather how well it performs without a lot of expense and preparation. If you think this may be you, then here is why you need to consider a siliconate concrete sealer.
What makes a siliconate sealer different than a coating is the fact that it actually penetrates (hence the name) into the concrete to create a protective barrier at the subsurface. They are also very easy to apply. Typically, the only bare concrete preparation required is to properly clean it first.
Other garage floor sealers such as acrylic, epoxy, and polyurethanes are topical in nature. They sit on top of the surface to form a protective film or coating.
With some exceptions, most topical sealers require additional concrete preparation other than cleaning in order for them to adhere properly. This can include sanding, etching, or even grinding the concrete surface.
Once applied, a siliconate sealer works by permeating into the pores of the concrete and chemically reacting with carbon dioxide. This reaction creates a cross-linking molecular membrane barrier that is almost gel-like and hydrophobic in nature.
This hydrophobic barrier is effective at repelling water and other liquids such as chemicals, and salty brines. In essence, water, automotive fluids, and most other liquids will tend to bead or sheet on the concrete instead.
How a siliconate penetrating sealer works on a concrete garage floor
Furthermore, the chemical reaction that fills the pores and capillaries within the upper surface of the slab has the additional benefit of slightly strengthening the surface of the concrete as well. While not as effective as a densifier for surface strength, it does help with surface wear nonetheless.
Concrete Siliconate Sealer Benefits
- Forms a hydrophobic barrier to help prevent intrusion of water and other liquids
- Reduces dirt buildup and deep staining
- Works to prevent pitting, spalling, and surface cracks from water absorption
- Reduces and may even prevent efflorescence
- Helps to prevent the harmful effects of road salts and deicing fluids
- Inhibits mold and mildew growth
- Breathable, water-based, and low in VOCs
- Excellent for garage floors, driveways, walkways, patios, and basement floors
- Low cost delivers one of the best values in concrete sealers
As stated, additional benefits to consider include mold and mildew resistance as well as protection from the harmful effects of road salts and deicing fluids. This means that if your garage temperatures drop below freezing overnight, the surface will be protected from the pitting and spalling that can occur due to the expanding effects of freeze-thaw cycles from melted snow and deicing fluids that can seep into the concrete.
Siliconate sealers dry to a natural-looking finish without any sheen. And because a penetrating sealer is non-film forming, it allows for the same anti-slip protection as bare concrete.
Furthermore, you don’t have to worry about damaging the sealer if you drag sharp objects across the garage floor when working on cars or projects. They are also a favorite concrete sealer for driveways, walkways, and patios.
Other factors to consider are expense and ease of application. This is what makes a siliconate concrete sealer for your garage floor one of the best values you can find.
Most 2-car garages will require only one or two gallons of sealer depending on the manufacturer. Cost is usually less than $50 a gallon for a quality product and application is much easier than applying a coating or even paint for that matter. Expect it to last up to 10 years or more before a new application is necessary.
One thing to be aware of is that concrete penetrating sealers do not seal cracks. Cracks will still need to be repaired first in order to seal the garage floor properly.
This post may contain affiliate links. If you use these links to make a purchase, we may earn a small commission. As an Amazon Associate, All Garage Floors earns from qualifying purchases. You can read our full disclaimer here.
Best Siliconate sealers that we recommend
There are two products we like to recommend that work extremely well and get great reviews.
The first is PS101 by Concrete Sealers USA. This siliconate sealer has a strong reputation for great performance and is known for lasting years. In fact, the reviews are outstanding.
It only wears down as the concrete wears down and can also be used as a “cure and seal” for new concrete.
Application is easy with no special mixing required. Expect a coverage rate of 300 – 450 ft² per gallon for machine troweled and smooth finishes.
Purchase PS101 Concrete Sealer – 1 Gallon
Purchase PS101 Concrete Sealer – 5 Gallons
If you like shopping from Amazon, you can find PS101 there as well.
Purchase PS101 – 1 Gallon From Amazon
Purchase PS101 – 5 Gallon From Amazon
Important to note; if you plan on using a siliconate sealer for a broom finish surface, Concrete Sealers USA recommends their PS102 Concrete Sealer.
PS102 also works extremely well for driveways, walkways, and patios. The reason for this is that these types of finishes are typically more porous than a steel troweled or machine troweled garage floor. PS102 is formulated for the more porous surface that these finishes provide.
Purchase PS102 Concrete Sealer
Expect a coverage rate of 200-300ft² per gallon of PS102 when applied to these types of surfaces. Just like the PS101, it can also be used as a “cure and seal” for newly poured concrete.
The second product we can recommend is Armor SC25 by Foundation Armor. Besides garage floors, this penetrating siliconate sealer is developing a strong reputation for use on driveways, walkways, patios, and basements.
The coverage rate is 200 – 250 ft² for machine troweled or smooth dense surfaces. Expect 100 – 150 ft² for a broom finish or rough surface.
Just as the PS101, SC25 is water-based and no special mixing is required. One note to make is that Foundation Armor does not recommend SC25 as a “cure and seal” for freshly poured concrete.
Purchase SC25 from Amazon – 1 Gallon
Purchase SC25 from Amazon – 5 Gallon
One thing to pay close attention to is the spelling of ingredients for some penetrating sealers. For example, a popular seller at home improvement centers is silicone sealers. Notice the difference? Silicone versus siliconate. It’s easy to miss this.
We do not recommend a silicone sealer for traffic areas such as a garage floor or outside on walkways, driveways, and patios. The reason is that they tend to sit more on top of the surface and do not penetrate as well.
Though they have good hydrophobic and oleophobic properties, they wear down at the surface extremely quickly and lose their sealing properties. Yearly reapplication is recommended. They also are not U.V. resistant and will deteriorate over time when exposed to sunlight.
Will a siliconate sealer stop oil stains in concrete?
This is one point that we want to make clear. Though siliconate concrete sealers can be somewhat resistant to oil stains, they are not stain-proof. In fact, there is not a penetrating sealer available that is. Only a commercial quality garage floor coating will provide close to stain-proof oil protection.
The reason for this is that penetrating sealers are non-film forming. Unlike coatings, they seal the concrete at the subsurface. However, what makes siliconate sealers unique is that they consist of a relatively larger molecular structure than many other types of penetrating sealers. This allows for better surface protection and better resistance to stains.
The best protection from oil stains when using a penetrating sealer is to clean them up as soon as you see them. Don’t let them dwell or sit for a long time. If they do sit, they will eventually seep into the very upper layer of the concrete surface and can leave a faint stain once cleaned.
If resisting oil stains are one of your primary concerns when choosing a penetrating sealer, then we suggest you read our review of PS100 Oil & Salt Repelling Sealer by Concrete Sealers USA.
In addition, GhostShield has a combination system for oil repellency that uses penetrating sealers as well. You can read our review of GhostShield 8510 and learn how this system works.
Applying a penetrating sealer to your garage floor
Make sure the surface of the garage floor is free of dust and oil. Clean up any oil spills that may have accumulated and scrub the surface of your garage floor with TSP and a stiff-bristled brush. A floor maintainer with a black pad works even better.
Rinse off the surface with a hose and let it thoroughly dry – usually, 24 hours is sufficient unless the humidity is up. When ready, apply the sealer with a low-pressure pump sprayer or roller and paintbrush. Do not let it puddle till dry or it will leave a white chalky substance that is hard to remove. The area should be ready for traffic in 12 hours. That’s it!
Once done, you will have a natural-looking surface that is protected for the next 10 years or more depending on traffic. So if you are the no-frills, “working” garage type of person that wants to protect their garage floor with minimal preparation and expense, then a siliconate penetrating garage floor sealer is definitely worthy of your consideration.
Lindsay Hough says
Thank you very much ! I have one last question – I read several of your articles and discovered the hydrochloric acid gel product for etching. My reading of these articles and your comments would be that the most superior etching job would still be with hydrochloric or phosphoric acid but we know the handling and potential safety issues. May I conclude that you think the gel-acid products are much better etching products than citric acid, yet not quite as effective as traditional hydrochloric acid? They seem to have the advantages of more environmentally friendly, & easier cleanup, but much more costly? I don’t mind the extra expense of the gel, but I do not want to compromise the etching quality since these epoxy coatings are thin. For light foot traffic, 2 cars in and out of a garage, and a clear coat on top of the rustoleum epoxy will I be happy with the acid-gel etch ? or is the good old toxic hydrochloric acid still the best possible prep for this job?
Shea says
The gel products work extremely well Lindsay. They are generally used by contractors where grinding is not an option. You may be spending more to etch your concrete with gels, however, than you have spent on the coating. If it were us, the standard muriatic or phosphoric acid etch is the more economically feasible choice for the inexpensive type of coating you have chosen to apply.
Lindsay Hough says
Post-etch follow-up and few more questions It’s a 500 sq ft new garage floor (3 mo concrete) and etching was not easy. After 2 treatments with 3:1 water:muriatic on first part of the floor with 5 min etching, I went to 2:1 water:muriatic for 15 min treatments and its mostly etched. After thorough hose rinsing, I power washed the entire floor and here’s what I have: Most of the floor resembles 100 to 150 grit sandpaper but there are still smooth spots. 1) Do I still need to remove these ? After it dried there is still residue on the floor (‘powder’ removed with a damp cloth). 2) Do I just have to keep power washing these until residue is gone? (I don’t think I have too much acid – baking soda solution does not react with damp spots). One area has some gold streaks (too much acid?). 3) Will epoxy cover these? One high acid area had some residue I tried to scrub and now I have a 1 in diameter hole (1/2 in deep). I have rinsed it, dried it and it has a gummy white material inside. 4) Can I use the rustoleum (or other) epoxy concrete patch for this, then epoxy seal over it? just patch this over the gummy stuff ? My plan is to patch the hole, power wash floor until residue is gone, pH check the dried/dampened floor, dry for 2 or 3 days then epoxy. …. Any feedback ???? Shea you have been SO helpful. Thank YOU !
Shea says
Wow, Linda. You went aggressively overboard on the etching. A 2:1 ration can damage your concrete as evident by the hole you have and the streaks in the concrete. The biggest concern is going to be if one coat of epoxy will be enough to get a good color uniformity due to the lower solids epoxy you are using. That aggressive of an etch is going to allow the concrete to absorb more of the coating than usual. It’s important that you get most of the white powder up. You have an excess amount of it due to the aggressive etch. The white powder is the concrete at the surface that was broken down. Power washing helps, just make sure you let the concrete dry for a few days or so. You can use the Rust-Oleum epoxy concrete patch providing the hole is dry and you get the gummy stuff out (can’t tell you what that is at the moment).
David Ruekberg says
Thanks for this and other articles. What do you recommend for removing old arcrylic sealer?
My garage floor was replaced in 2010, very good job, but they used an acrylic sealer which only lasted a couple of years. I put on another coat and it also started peeling quickly. I plan to go with your suggestion of using PS101 penetrating sealer.
We live in upstate New York and salt in the winter is a given. I want to protect the floor, I don’t care about shine. But I am confused about how to get the old sealer off. My first thought was sand or grind, but the chemical removers sound less messy, kind of (no dust; our garage is under the house, and next to the basement). I looked at Blue Bear 600GL, but cleanup is tricky. No drain in the garage, and I can scrape most of it into a bucket. Then I would need to go over with a degreaser a few times. Disposing of the degreaser is even trickier. Otherwise, it means hosing it out onto the asphalt driveway. EasyStrip 1000 seems another possibility.
Your recommendation would be much appreciated. Thanks.
Shea says
Most of the ECO friendly strippers work just as you stated, David. They are still messy since the floor needs to be scraped and rinsed with a high pressure nozzle. We prefer the FranMar products (Blue Bear) if you choose that route. Grinding is our preferred method since you get a consistent outcome and finish. If you grind with a vacuum setup you can really keep the dust down. It requires a dust shroud on your grinder and a Dust Deputy setup between the grinder and shop vac. Either way, removing topical sealers is never a simple project. You just have to pick your poison and go from there.
David Ruekberg says
Thanks, Shea. I found your article on grinding after I posted that. It looks like the best route. I really appreciate your feedback. This site is AMAZING!
David Ruekberg says
Sorry, just had 2 more questions:
1) In grinding the floor, do I need to use the Diamabrush coating removal tool and then the concrete prep tool, or just one or the other? The surface is still in good shape, but I want to get the old coating off.
2) Can epoxy eventually be used over the siliconate sealer? I plan to only use the siliconate, but if a future owner wanted to use epoxy on top, I’d like to know what to tell them.
Thanks again.
Shea says
Just use the coating removal tool David. The process of removing the coating will prep the concrete as well. Yes, you can apply epoxy over the sealed concrete, but it will require grinding again to provide a mechanical bite for the epoxy to adhere well.
Doug skillin says
Thank you for your articles.
I have a 2 year old 22×22 garage floor (old one sunk into the ground after 5 years,don’t ask) we now have a expansion crack forming and we need to repair it and then seal the floor, we live in northeast and want to protect it. I think the penetrating siliconate sealer sounds great, but my wife says she wants it “refreshed, all one new color” as well. Questions are #1 do these sealers color the floor at all? #2 can we have the floor cleaned and painted with a masonry paint before sealing? And #3 could we paint over the siliconate sealer? We really don’t care about high gloss or colors so epoxy type sealers are not needed.
Thank you in advance for your help.
Shea says
Hello Doug. Here are the answers to your question.
#1 Penetrating sealers do not color the concrete. They leave it looking pretty much as it did before the sealer was applied.
#2 Masonry paint is not a sealer and you cannot seal over masonry paint.
#3 Yes, you can “paint” over a siliconate sealer with masonry paint. It’s actually considered a primer for that. Keep in mind, however, that masonry paint will not hold up over a northeast winter. You will be repainting in spring time. The concrete will stay protected by the siliconate sealer though even if the paint is damaged.
If it’s in the budget, you may want to consider a single-part polyurea floor coating if you want a solid color garage floor. It is as easy to apply as paint and it seals the concrete as well. Two coats will stand up to northeast winters without issue and will last for years. You would not use a siliconate sealer prior to application and it does require that you properly prep the concrete by acid etching first.
James G Anderson says
Not available from Amazon.
Shea says
Thanks for pointing that out James. We put in an inquiry to find out why. It’s a very popular product and may be that they shut down for the holiday at the end of the year. UPDATE: Yes, it was as thought. Concrete Sealers USA shuts down for the holiday. They will be back up and shipping after the holiday.
kim says
Question. We just bought a new house and I want to seal the garage floor myself. I want the easiest to apply (roller paint?) I want the sealer to make it easier to sweep the garage clean. I don’t really care how it looks. Basically, I want a clean garage. What is the best product to use? Thanks
Shea says
Hello Kim. A penetrating sealer that the one discussed in this article is not going to make sweeping easier. Penetrating sealer do not change the surface of the concrete. If you want to do that, they you will need to use a topical, film forming sealer. In other words, some type of coating. The coating is what makes the sweeping real smooth. If all you do is park vehicles in your garage, then you may want to consider an acrylic sealer. An MMA acrylic sealer like this one here is fairly tough and easy to apply.
Dan says
Hello, great articles on this, but I’m having some confusion still. I really like the durability of the penetrating sealers discussed in this article as my garage will be used as a working garage (floorjacks, jackstands, etc..) though I was also looking for something that will somewhat smooth the surface and give a more finished appearance that I wouldn’t need to worry about damaging. I fear hot tire pickup or chipping with epoxy or any other topical coating. Is there a penetrating sealer you can reccomend that will make sweeping/moping easier while still penetrating into the concrete so it won’t suffer chipping/hot tire pickup?
Shea says
Hello Dan. Concrete sealers are either penetrating or film forming (coating). Anything that creates a smoother surface is going to be film forming. Unfortunately, the home improvement store DIY epoxy kits are responsible for the bad reputation that epoxy can get about hot tire pickup, peeling, and etc. A properly prepared concrete surface with a commercial quality coating system will perform for years without experiencing the common mishaps of those epoxy kits. That is why the commercial quality garage floor coating market is growing at a fast pace.
That said, we understand fully why some people don’t want to deal with a coating. However, if you want something that is going to smooth out the surface of concrete, then a coating is your only option. Penetrating sealers form a molecular barrier at the sub-surface. This is why they last so long and don’t have issues with peeling, scratching, and etc. They do not change the texture of the surface. Some can be fairly stain resistant (providing fluids aren’t allowed to sit for long periods), but they are not resistant like a coating is. If you have a smooth troweled surface to begin with, then one exception would be a stain guard. These are typically used on polished concrete. Multiple applications of a stain guard can leave an extremely thin film on the surface that can make sweeping and mopping easier. This article here is a good example. Note that this reader had a machine troweled surface to begin with. It will not work on a broom finish or most hand troweled finishes unless it turned out fairly smooth.
One other option that is new to the market would be a product called TS210. You can read about it here. This is actually an acrylic modified polyurethane sealer that leaves a very thin coating on the floor. It’s highly chemical, stain, and scratch resistant. Plus, you will not experience hot tire pickup and it’s easy to repair. Something like this would smooth out the surface enough to make mopping and sweeping a breeze.
Dan says
Awesome! Thanks! I’m going to most likely go with the TS210. Seems to fit my needs pretty much perfectly! Thanks again!
Dan says
Hello, so I finally am moving into my new home purchase, and I’d like to use the Ts-210 on the floor, but the floor has an old peeling layer of paint on it. What would you reccomend to remove the paint?
Shea says
Hello Dan. You need to first remove the paint via grinding or chemical stripping. Of the two methods, grinding is the fastest and the less messy.
Paul Leonard says
Hi. Will this work as a radon sealer? Thanks.
Shea says
Hi Paul. You actually ask a great question. Sealing your concrete will not stop or significantly reduce radon intrusion, despite the fact a few companies have made a great business selling products that they claim will stop it. In fact, some states have actually issued consumer notices that warn people of the use of sealers to prevent radon intrusion. This here is an example. The EPA actually speaks of the ineffectiveness of concrete sealers in a consumer guide about radon as well. You can read it here. Page 11 has the information about sealing. While sealing the concrete and all cracks will assist in the process, the only way to stop radon intrusion is with a proper radon ventilating system.
Allan says
Used PS101 penetrating sealer on 7 year old indoor 3-car garage floor that was beginning to spall from winter salts etc. Next day large various areas had dried white and should dry clear. Did not apply heavily and no puddling. Lightly power washed these areas to try and mitigate/remove white areas; very, very, very difficult. Had to towel wipe material after four washes to make fairly presentable, hours to accomplish . The garage floor is trowel finish surface and PS101 sealer was supposed to be applicable.
Shea says
Hello Allan. I’m sure you feel it was applied correctly. However, any time you get white residue from a penetrating sealer it’s from too much being applied and allowed to dry and evaporate on the surface. The coverage rates of penetrating sealers always vary depending on the surface. If your surface was smooth troweled, it would require less than is typical. Did you test the surface for porosity first before application as the instructions indicate? If you are still having issues, we suggest you contact Concrete Sealers USA and speak with them. Their customer service is excellent.
Mark Bennett says
I have a new concrete garage floor (14 days), the floor has not been driven on and has been rinsed & sweep clean. Do I need to etch it before applying a penetrating sealer at the 30 day mark.
Shea says
Hi Mark. Unless the floor was power troweled to a very smooth finish that will absorb little water, it will not be necessary to etch. You check by applying drops of water to the concrete. If it is absorbed within a few minutes then you are good to go.
Luis Romero says
Hello there,
I recently sealed my garage floor using Armor CS25.
It was mentioned that after sealing you could paint the floor.
could 1 part epoxy or acrylic paint be good options to paint over with this sealer?
Thank you.
Shea says
Hi Luis. We know that the manufacturer’s of penetrating sealers tend to make this statement. However, we have never thought it a good idea. The reason is that the sealer effective ly prevents the paint from penetrating into the concrete in order to get the best mechanical bond. If the surface has a rough texture to begin with, then you may be OK for just an acrylic paint or 1-part epoxy paint. However, it will not work at all for a true coating such as 2-part epoxy or similar coating. Those type of products are sealers in their own right and need the floor properly prepped first via acid etching or grinding.
Luis Romero says
Thank you for your answer Shea.
I’ve learned a lot from reading your articles.
I resurfaced my garage floor using polymer modified mortar before sealing. My garage floor was extremely spalled and pitted so this step was a must. My garage is also my basement so there is a little bit of a moisture problem so I figured a siliconate coating would mitigate the problem a little bit.
The finish on my garage floor is sort of rough troweled; I went over with a 20 grit rub brick to smooth out sharp trowel marks.
I’m not sure if this texture would be rough enough for paint to adhere properly. I’m having a hard time deciding.
What’s your opinion based on this description?
Do you think I should give it a shot and paint over it with a 1 part epoxy paint?
Keep up the good work!
Shea says
The surface ought to be fine for just paint, Luis. Paint will breathe a little and allow some moisture vapor to pass, but if you get too much it will peel. Another option would be to apply a clear acrylic coating such as this one here. These breathe and will allow some moisture to pass as well.
Marc Meierle says
I am looking for something that will stop moisture from coming up through the concrete (yes the nut job did not put a vapor barrier down) hence need something to stop it from coming up through and making the concrete surface wet. Please help
Shea says
Hello Marc. There is not a sure-fire cure that works every time to stop moisture from coming up through the concrete. It’s much easier to block from underneath (moisture vapor barrier) than from the top. Is your slab below grade or above grade? Does it happen only during wet months or all year long? Have you done some of the obvious things like make sure water drains away from the slab and not sit up against it? Do you have any drains or water pipes that run under the slab that may be leaking? The most cost effective remedy is to apply a densifier. We explain how they work here and also review a good product here. Depending on the conditions of your slab, densifiers will either slow down intrusion or stop it completely. After that, the only other treatment are special moisture vapor blocking epoxy coatings. These are expensive and require aggressive grinding of the slab before they can be applied.
kyle says
i have a 25 year old working garage floor – cars havent seen the garage floor in almost 20 years. i have issues with musty mold smell, and mice problems – droppings etc. i dont want a polished or gloss finish. and i need something that wont scratch. in terms of prep – i would etch if i had to – but i know i wouldnt grind it down. sooo ?? what is the right product – also looking for longevity as my garage is filled with tools and i dont want to pull everything out of my garage every 2-3 years
Shea says
Hello Kyle. Penetrating sealers, such as the ones we discuss in this article, do not change the look of the concrete and generally do not need any special prep other than a clean surface free of dirt, oils, and etc. Because they are penetrating, they do not leave a coating on the surface that can peel, chip, and etc. They generally will last up to 10 years or so before reapplication may be necessary. The PS101 and PS102 that we discuss here would be a great candidate based on your needs.
Mike Sackett says
Can you put a sealer on top of a penetrator in order to protect from stains, or does the sealer negate the penetrator? I am having a new house built and I would like to take care of the floor before we move in. I should be well past the 28 day cure time. Thank you
Shea says
Hello Mike. I think there may a confusion in terms. What type of product do you mean exactly when you say a sealer?
Mike says
Anything that prevents a fluid from soaking into the concrete
Shea says
Hi Mike. A penetrating sealer is never going to completely block any fluids from soaking into the concrete over time. The only way to prevent that is to use a film forming topical sealer (coating).
Mike says
Thank you
Dennis Johnson says
Can these sealers be applied over polymer-modified cement patches?
Shea says
Hi Dennis. They can be applied over them, but they don’t do much since the polymer patch lacks many of the minerals that the sealant reacts with to form a seal. However, polymer-modified concrete is much less porous than standard concrete. Dirt, liquids, and other contaminants tend to sit on the surface and are easier to clean. This is why they are also resistant to freeze thaw damage.
Mike E says
We would like to refinish our basement concrete floor, but it was painted well before we purchased the house in ’89. Years later, the thin layer of gray paint is slowly flaking off which probably creates more of a dust problem than if it had been left as bare concrete. Assuming that we need to remove the paint prior to applying a penetrating sealer, what is the best way to go about such a thing without filling the house with concrete and old paint dust? Thanks!
Shea says
Hi Mike, Yes, you would need to remove the paint first before applying a penetrating sealer. We would recommend stripping the paint with an Eco friendly paint stripper. This one by Franmar is an example. Once you remove the paint, you will need to scrub the concrete with a degreaser or a solution of warm water and laundry detergent. If your basement doesn’t have a drain, you can use a wet rated shop vac to suck up the soapy solution and then the rinse water. You will want to let the concrete dry for a full week before application of a sealer since it’s a basement. A dehumidifier and fans will speed up the process.
Mike E. says
Thanks, Shea!
Dan says
Can I paint a garage floor or driveway before applying siliconate product?
Shea says
Hi Dan. No, you can’t do that. Penetrating sealers work on bare, untreated concrete only. If you apply it after the concrete was painted or had a coating applied, the siliconate sealer would just sit on top and evaporate since it can’t come in contact with the concrete.
Dan says
ok, thanks. So what would be the best product to do a concrete driveway. I would like to paint it first to make the colour more unified, and then maybe seal it. But I heard there is a rubber based paint that basically do both parts. I live in Canada so the weather is a big factor for concrete freezing/thawing.
Shea says
Hi Dan. The problem with applying any type of coating to a driveway, particularly one that sees winter snow, is that it will make the driveway extremely slick. You can use an aggressive anti-slip additive in the coating to combat that, however, shoveling the driveway, snow blowers, and etc. will damage the coating regardless.
Shane says
Is the siliconate slick for a garage floor? If so, what anti-slip additive do you recommend to add with PS101? Thanks!
Shea says
Hi Shane. No, a siliconate sealer is not slick. It is a penetrating sealer and does not leave a film or topical coating on the concrete. The concrete will retain the same slip resistance that it currently has.
Shane Davis says
Thanks. Is this the best cheap option in your opinion? I was going to go with an Epoxy/polyurethane but decided that money could be better spent other places.
Shea says
That depends, Shane. What is your goal for the floor exactly?
John McG. says
Very helpful articles. Thank you. My 50 year old large insulated double detached garage has a damp floor which I will address soon. Worse though is springtime seepage along 3 walls where the foundation (3 courses of cinder blocks most of which is below grade) sits on the old concrete pad. My plan is to expose this foundation/slab area on all three sides (digging by hand) and seal the join with tar, deposit drainage gravel below the join and then back fill. I know there are membrane and weeping tile options. For a home foundation I would consider these but for a garage??? The garage is heated with a forced air unit. I did not see any articles on this leaky floor problem but welcome any advice you have. The garage is in Calgary Alberta. Thank you.
Shea says
Hi John. If the water is not successfully redirected away from the foundation, then you will always experience some degree of dampness in the garage. Applying a sealer to the garage floor is not going to stop it. Digging around the affected perimeter walls and back filling with gravel will definitely help. With all that labor invested, I’m not sure why you would not want to take the extra step and lay the perforated pipe for a French Drain, but that is up to you. We would also recommend sealing the exposed cinder block on the outside that will otherwise be covered. These steps should eliminate the dampness problem.
John McGurran says
You are right about the pipe. I will add it to the job. I was planning to seal the join but could easily cover the exposed blocks. I read that I could add 2” Pink foam board to the outside which might help with insulation. It has the same R10 value as the garage door.
Thanks very much for your reply and valued advice.
Mark Rolfsmeyer says
Great web site! I have a new detached garage,( heated floor), with a hand troweled concrete, 6 mo. old. I want to use a penetrating sealer, I’m wondering if I should use the PS101 or PS102. the floor is fairly smooth but not machine smooth. Thank You
Shea says
Hi Mark. If it was finished troweled with a steel trowel and not broom finished, then you will want to use the PS101.
Mark Rolfsmeyer says
Yes steel trowel finished, I will use PS 101, thanks for the reply. Very informative site I was going crazy trying to research sealers, or epoxy’s.
Erik Olson says
I have a 24×40 crawl space that is near a lake and poured below high watermark. Drain tile and sump pump redirect water well. The cement floor “dusts”. Per a contractor the Cement is soft. The contractor recommended applying lapidolith to stop the dusting. Do you have a recommendation?
Shea says
Hi Erik. Lapidolith is a magnesium fluorosilicate densifier. It requires scrubbing into the concrete properly for application. For the same results, we would recommend using lithium densifier. These are much more common and easier to apply since they do not require scrubbing into the concrete. We would recommend PS103 by Concrete Sealers USA. This is a great product and the customer service is good as well. Just give them a call if you have any questions.
Chris Miller says
I have a new 2+ car garage and am getting ready to install swisstrax but was thinking of sealing the floor below the install. I’ve read about a lot of the different products and am leaning towards PS101. The garage will be used to work on my cars but any spills would be cleaned up very soon after they happen. Any ideas or input on whether PS101 will suit my needs or is there something else out there that is reasonably priced and is easy to apply?
Shea says
Hi Chris. Testing by Concrete Sealers USA has revealed that PS104 will actually do a better job at resisting petroleum stains if that is your main concern. It’s a densifier with siliconate sealer added. This article here explains how such a product works. It’s similarly priced and easy to apply. They also recently released a new product called PS100 that has excellent oil repellency, but it is more expensive and may be a bit overkill for application under tiles. We did a review of it here.
Lou G says
Hi,
Again, thanks for this amazing information on concrete floor.
I have a 2 months poured concrete slab that has been hand troweled (the surface is not as soft as if it had been mechanically trowelled). In this case, is the PS102 Rough surface siliconate sealer a better option than the PS101 smooth surface?
Also, this is not my objective right now but I am wondering if a topical scelant or finish could be added later.
Thanks a lot!
Lou
Shea says
Hi Lou. If the surface is not a smooth finish, then the PS102 should be used instead. Good examples are driveways, walkways, patios, broom finishes and etc. If you want to apply some sort of topical finish at a later date, it will require grinding to remove the PS102 first.
Scott M says
Hello-
I have a 20 year old basement floor with soft/dusty edges near the verticle walls (about 24″ wide in most areas). When the floor was poured we were hit with heavy rain and the outer edges of the pour ended up getting alot of the “”cream” from the pour. I have been searching for years to find a product that I can put on the softer/dusty areas to “seal” it. I am not concerned about weight bearing as the area only gets foot traffic.
Can you advise a product and process?
Shea says
Hi Scott. If you don’t want to change the look of the surface, then we would suggest applying a densifier to those areas. If the dusting is not severe, it will help to reduce it and sometimes even stop it. This product here is one we recommend.
If the dusting is more heavy and you don’t mind changing the way the concrete looks, then we recommend applying a water-based acrylic sealer. Acrylic sealers are clear coatings that breathe and will allow small amounts of moisture vapor to pass through and not get trapped under the coating. You can usually find these are your local home improvement centers. This will completely stop the dusting unless it’s so severe that the concrete breaks down into dust under the coating and it delaminates. If that were to happen, you would need to grind the surface to remove the soft concrete layer before applying anymore sealers.